background image

9

FLIGHT READINESS INDICATORS

These indicators give you vital information about flight 

readiness status. 

Treat them as a go / no go for flight.

Do 

not

 attempt a take-off if they do not show that the drone is 

ready for flight.

Receiver Decoding Indicator (white)

Front-bottom indicators (red)

Back-bottom indicators (green)

Back-bottom indicators (green)

Front-bottom indicators (red)

Controller Signal Strength (White)

The white bars on the drone illuminate steadily when controller 

signal strength is within specification.

The white bars flash rapidly or slowly when controller signal 

strength is not within specification.

Critical Battery Level (Red and Green)

If battery voltage reaches critical level, or less than about 

10.4 V, the red and green bars will flash slowly and the Critical 

Battery Level Alarm will sound.

Motor Unlocking (Red)

The red bars on the drone illuminate steadily once the motors 

are unlocked. They will fash quickly when the motor is locked. 

Motors must be unlocked

GPS Signal Strength and Critical Battery Level (Green)

The green bars on the drone illuminate steadily when GPS 

signal strength is within specification.
If GPS signal strength is not within specification, the green 
indicators will flash.

LED Indicators

Содержание GIGA-8000





























Отзывы: