Moroso 74018 Скачать руководство пользователя страница 6

 

 

 

 

   

VOLTAGE SELECTOR SWITCH                                                             

 

VOLTAGE SELECTOR SWITCH

 

 

WARNING

 The front panel switch has two settings, marked  

12V and 16V, with OFF in the center. 
The switch must be set to 12 Volts when charging 12 Volt  
(SIX CELL) batteries. 
The switch must be set to 16 Volts ONLY when charging  
16 Volt (EIGHT CELL) batteries. 
Sixteen Volt (Eight Cell) batteries are special high performance 
batteries used in racing applications only, which need a higher  
voltage recharge. They are identified as 16 Volts on the battery  
label, and have eight cell caps on top of the battery. 
 

Setting the charger to 16 Volts

, when connected to  

the "12-Volt Post" on a three terminal 16 Volt battery, will apply 
excessive voltage to the battery cells and to the vehicle  
electrical system, and may result in emission of explosive  
gasses, overheating and damage to the vehicle electrical system.  
Damage caused by incorrect setting of the Voltage is not covered  
under the warranty, so check which type of battery is connected  
before using the charger. If in any doubt, use only the 12 Volt  
setting. 
 
  

CHARGER LOCATION 

 
1. Locate charger as far away from battery as charging cables  
    will permit. 
2. Never place charger above battery being charged; gasses 
    from battery will corrode and damage charger. 
3. Never allow battery acid to drip on charger when reading 
    specific gravity or filling battery. 
4. Do not operate charger in a closed-in area or restrict 
    ventilation in any way. 
5. Do not set a battery on top of charger. 
 
 

 Installation Instructions Cont.                                                                        Page 6 of 14            

Installation Instructions Cont.                                                                        Page 6 of 14            

WARNING

 The front panel switch has two settings, marked  

12V and 16V, with OFF in the center. 
The switch must be set to 12 Volts when charging 12 Volt  
(SIX CELL) batteries. 
The switch must be set to 16 Volts ONLY when charging  
16 Volt (EIGHT CELL) batteries. 
Sixteen Volt (Eight Cell) batteries are special high performance 
batteries used in racing applications only, which need a higher  
voltage recharge. They are identified as 16 Volts on the battery  
label, and have eight cell caps on top of the battery. 
 

Setting the charger to 16 Volts

, when connected to  

the "12-Volt Post" on a three terminal 16 Volt battery, will apply 
excessive voltage to the battery cells and to the vehicle  
electrical system, and may result in emission of explosive  
gasses, overheating and damage to the vehicle electrical system.  
Damage caused by incorrect setting of the Voltage is not covered  
under the warranty, so check which type of battery is connected  
before using the charger. If in any doubt, use only the 12 Volt  

      setting 
 

    

CHARGER LOCATION 

 
1. Locate charger as far away from battery as charging cables  
    will permit. 
2. Never place charger above battery being charged; gasses 
    from battery will corrode and damage charger. 
3. Never allow battery acid to drip on charger when reading 
    specific gravity or filling battery. 
4. Do not operate charger in a closed-in area or restrict 

          ventilation in any way. 
      5. Do not set a battery on top of charger. 

 
 
 

Содержание 74018















Отзывы: