Moroso 74018 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 14

Moroso 74018 Скачать руководство пользователя страница 12

Installation Instructions Cont. Page 12 of 14

Installation Instructions Cont. Page 12 of 14

3. The Microprocessor Control can indicate a problem with the

battery. If the battery has not reached the First Stage of the
Operation within 18 hours, the charger may determine that
a problem exists within the battery or the battery is too big
for the charger's output rating.

The OVERRIDE TIMER FUNCTION is shown by the GREEN
LED FLASHING.

SERIES AND PARALLEL CHARGING

1. Two 6 volt batteries may be charged with the 12 volt

charger if they are connected in SERIES as shown below:

3. The Microprocessor Control can indicate a problem with the

battery. If the battery has not reached the First Stage of the
Operation within 18 hours, the charger may determine that
a problem exists within the battery or the battery is too big
for the charger's output rating.

The OVERRIDE TIMER FUNCTION is shown by the GREEN

LED FLASHING.

SERIES AND PARALLEL CHARGING

1. Two 6 volt batteries may be charged with the 12 volt

charger if they are connected in SERIES as shown below:

CAUTION: NEVER UNDER ANY CIRCUMSTANCES
ATTEMPT TO CHARGE A SINGLE 6 VOLT BATTERY WITH
THIS CHARGER. THIS WILL RESULT IN SERIOUS DAMAGE
TO THE BATTERY AND CREATE A RISK OF EXPLOSION.
EXTREME CARE SHOULD BE TAKEN TO CONNECT THE
BATTERIES ONLY AS SHOWN ABOVE. IMPROPER
CONNECTION CAN RESULT IN EXPLOSION AND
SERIOUS INJURY.

CAUTION: NEVER UNDER ANY CIRCUMSTANCES

ATTEMPT TO CHARGE A SINGLE 6 VOLT BATTERY WITH
THIS CHARGER. THIS WILL RESULT IN SERIOUS DAMAGE
TO THE BATTERY AND CREATE A RISK OF EXPLOSION.
EXTREME CARE SHOULD BE TAKEN TO CONNECT THE
BATTERIES ONLY AS SHOWN ABOVE. IMPROPER
CONNECTION CAN RESULT IN EXPLOSION AND
SERIOUS INJURY.

«
...
10
11
12
13
14
»

Содержание 74018















Отзывы:

Нет отзывов