Morningstar SureSine 1000 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 61

Morningstar SureSine 1000 Скачать руководство пользователя страница 18

10

MS-003650

(Rev B08)

INSTALLATION

2.3.2 Mounting

Procedure

To secure the inverter to the mounting surface:

1. Place the SureSine on the surface where it will be mounted and

determine where the wires will enter/exit.

• Be sure there is sufﬁ cient bending room for the wires and other

auxiliary connections, as required by local code.

• Verify that the mounting screws will not penetrate wires or other

objects located on the opposite side of the surface.

• Ensure the surface is strong enough to support the weight of the

inverter and anything else mounted on it. It may require additional
support, such as a sheet of plywood.

2. With a pencil or pen, mark the mounting hole locations.

3. With a drill and 1/8” (3 mm) bit, drill pilot holes for each of the four

mounting screw locations marked on the mounting surface.

4. Place the SureSine onto the surface and align the mounting feet holes

with the four pilot holes. Use the #10 screws (included) to secure the
SureSine to the surface.

«
...
16
17
18
19
20
...
»

Содержание SureSine 1000






























































Отзывы:

Нет отзывов