Montigo P38DFL Скачать руководство пользователя

Страница: 32 / 36

Page 32

P38DF* Indoor Gas Fireplace

XG0193 - 150204.1

Appendix

Appendix A: Venting Terminations

Location

Canada*

USA**

clearance to the termination frame above grade, veranda, porch, deck, or balcony

12 inches

clearance to top of doors or operable windows

12 inches

clearance to sides or bottom of door or operable windows

12 inches

9 inches

clearance to permanently closed window when installed with approved glass penetration termination

clearance to permanently closed window Recommended to prevent condensation

16 inches

clearance to ventilated soffit located within a horizontal distance to 24 inches from centerline

of termination

22 inches

clearance to unventilated soffit

30 inches to combustibles

16 inches to non-combustibles

30 inches to combustibles

16 inches to non-combustibles

clearance to outside corner

9 inches

clearance to inside corner

12 inches

clearance to each side of the vertical centerline of a metre or regulatory assembly to a maximum

vertical distance of 15ft

3 feet

clearance to service regulator vent outlet

3 feet

clearance to non mechanical air supply inlet to the building or combustion air inlet to other
appliance for appliance <= 100.000 BTU/H (30 KW)

12 inches

clearance to forced air supply inlet

6 feet

3 feet above air inlet

clearance above paved sidewalk or paved driveway located on public property

7 feet

clearance under veranda, porch, deck, or balcony

22 inches to combustibles

16 inches to non-combustibles

22 inches to combustibles

16 inches to non-combustibles

clearance above roof

2 feet

clearance to adjacent walls and neighboring buildings

2 feet

18 inches

clearance from corner in recessed location

12 inches

Maximum depth of recessed location

4 feet

Maximum width for back wall of recessed location

2 feet

Horizontal clearance between two terminations that are level

Horizontal clearance (centre to centre) between two terminations that are not level

18 inches

Note 1: For N a vent shall not terminate directly above the sidewalk or paved driveway which is located between two single family dwellings and serve both dwelling.

Note 2: For P only permitted if veranda, porch, deck, or balcony is fully open on a minimum of two sides beneath the floor

Note 3: For J, K, and as specified in CGA B149 installation code. Local codes or regulations may vary.

* Based on CGA B149.1 Natural Gas and Propane installation code. Local codes may vary, please check with local regulatory agency.

** Based on ANSI Z223.1/NFPA 54 National Fuel Gas Code. Local codes may vary, please check with local regulatory agency.

Содержание P38DFL





































Результаты поиска

Содержание P38DFL

Отзывы:

Похожие инструкции для P38DFL

Бренды по названию

Популярные бренды

Montigo P38DFL, Инструкция по установке и обслуживанию

Результаты поиска

Содержание P38DFL

Отзывы:

Похожие инструкции для P38DFL

Бренды по названию

Популярные бренды