Montigo P38DFL Скачать руководство пользователя

Страница: 30 / 36

Page 30

P38DF* Indoor Gas Fireplace

XG0193 - 150204.1

Maintenance

Troubleshooting:

SIT Proflame 2:

The following is a troubleshooting chart of possible problems:

PROBLEM

SOLUTION

Pilot won't ignite or spark. - Check the on the batteries on the

remote or the receiver.
- Check the green LED on AC adaptor
-Check the green ground wire under

the valve

Main burner will not light.

- Check the wiring on the valve as per

diagram

One or more light bulbs are

not working

- Contact the local dealer for repairs

or service

Fan not working

- Make sure the fan speed control is on.
- 10 minute delay to turn on.

If your fireplace still does not operate correctly, consult your local Montigo dealer.

All service and repairs should be performed by a qualified Technician.

All spare parts, optional fans, and optional trim finishes are available from your local Montigo dealer.

Figure 27

. Remove the up-lighting glass from the burner tray.

Replacing Light Bulbs

The

P38DF*

light bulbs can be replaced in a few simple steps. Follow

the directions for removing the door on

page 20.

Once the door has

successfully been removed, proceed with

figures 27 - 27b

Figure 27a

. Wear gloves when handling light bulbs. To remove

a light bulb, pull connecting wire away from bulb and pull

light bulb up. Replace with new light bulb.

Figure 27b

. Rotate newly replaced bulbs in a full circle. Place

glass cover back in the burner tray.

Содержание P38DFL





































Результаты поиска

Содержание P38DFL

Отзывы:

Похожие инструкции для P38DFL

Бренды по названию

Популярные бренды

Montigo P38DFL, Инструкция по установке и обслуживанию

Результаты поиска

Содержание P38DFL

Отзывы:

Похожие инструкции для P38DFL

Бренды по названию

Популярные бренды