Montigo P38DFL Скачать руководство пользователя

Страница: 3 / 36

Page 3

Indicates a hazardous situation which, if not

avoided, WILL result in death or serious

injury or property damage.

Indicates a hazardous situation which, if not

avoided, COULD result in death or serious

injury or property damage.

Indicates a hazardous situation which, if not

avoided, WILL result in minor or moderate

injury.

Addresses practices that are important, but

not related to personal injury

DANGER

WARNING

CAUTION

NOTICE

P38DF* Indoor Gas Fireplace

Safety Alert Key

Introduction

XG0193 -150204.1

Introduction

Congratulations on your purchase of a

Montigo Fireplace

With over 30 years of experience, Montigo is committed to providing

you with a gas fireplace that is not only a beautiful addition to your

space, but that is also designed and manufactured to the highest

safety, reliability and engineering standards.

We strongly encourage you to read and carefully follow the instructions

laid out in this Installation, Operation and Maintenance Manual

and retain it for your future reference. Pay special attention to all

cautions, warnings, and notices throughout this manual intended

to ensure your safety.
This manual covers installation, operation and maintenance. Lighting,

operation and care of this fireplace can be easily performed by the

homeowner. All installation and service work should be performed

by a qualified or licensed installer, plumber or gas fitter as certified

by the state, province, region or governing body where the fireplace

is being installed.
This installation, operation and maintenance manual is applicable

to the models described to the right. Refer to your rating plate to

verify included options.

Warranty and Installation Information: (See Appendix B)

The Montigo warranty will be voided by, and Montigo disclaims

any responsibility for the following actions:

► Modification of the fireplace and/or components including

Direct-Vent assembly or glass doors.

► Use of any component part not manufactured or approved

by Montigo in combination with this Montigo fireplace system.

► Installation other than as instructed in this manual.

Consult your local Gas Inspection Branch on installation

requirements for factory-built gas fireplaces. Installation & repairs

should be done by a qualified contractor.

Safety Alerts

MODEL

Natural Gas

Liquid Propane

Gas Rating (BTU hr)

Linear Burner w/ Glass media Accessories

SIT Electronic Ignition

P38DFNI

25,000

P38DFLI

25,000

Young children should be carefully supervised when they are

in the same room as the applicance. Toddlers, young children

and others may be susceptible to accidental contact burns. A

physical barrier is recommended if there are at risk individuals

in the house. To restrict access to a fireplace or stove, install

an adjustable safety gate to keep toddles, young children and

other at risk individuals out of the room and away from hot

surfaces.

CAUTION

Содержание P38DFL





































Результаты поиска

Содержание P38DFL

Отзывы:

Похожие инструкции для P38DFL

Бренды по названию

Популярные бренды

Montigo P38DFL, Инструкция по установке и обслуживанию

Результаты поиска

Содержание P38DFL

Отзывы:

Похожие инструкции для P38DFL

Бренды по названию

Популярные бренды