Page 2
XG0752- 160902
LDVPV58 Linear Power Vent
Introduction ................................................................................ 2
Installation
Venting Installation ....................................................3 - 4
Power Vent - Horizontal Vent ............................. 3
Power Vent - Horizontal / Downward Vent ......... 3
Power Vent - Vertical Vent ................................. 4
Power Vent Installation................................................... 5
Wiring Instructions.......................................................6-7
Warranty ..................................................................................... 8
Termination Locations ................................................................. 9
General Information
This installation guide covers installation of the
LDVPV58
Linear Power
Vent System only. This system is designed to allow installation of gas
fireplaces that
cannot be done
with a standard Direct Vent gas
fireplace installation.
Specifications and instructions pertaining to your chosen fireplace must
be followed. Please read this Installation Operation and Maintenance
Instructions carefully before operating this equipment.
Standard Series (5"/8" dia.) Termination System:
LDVPV58 - Linear Power Vent System
Pre/Post Purge Control Box (ECA045PC, ECA062PV)
Power Cord Harnesses:
EPVH-10 10 foot power cord and harness
EPVH-20 20 foot power cord and harness
EPVH-40 40 foot power cord and harness
EPVH-60 60 foot power cord and harness
EPVH-80 80 foot power cord and harness
Selecting and Installing the Power Vent
The Linear Power Vent System must only be used with a Montigo Direct
Vent Fireplace. When selecting Venting components for use with this
Linear Power Vent System, take into consideration the various require-
ments required for the vent installation section of the Model's manual:
Models Must Be Equipped with Electronic Ignition
Only models equipped with an electronic ignition system may be installed
with the Linear Power Vent System. The absence of a standing pilot in
this system, allows for greater flexibility on venting requirements. For
example downward vertical vent runs are possible with an electronic
ignition system, as outlined in the Venting Section.
Table Of Contents
Introduction
Before You Begin
Minimum clearances of 1" from vent to all combustible materials
must be maintained.
The
LDVPV58
must only be installed with Montigo venting
components. The
LDVPV58
may be used with any of the
available Montigo terminations.
Installation of the LDVPV58 must comply with this manual, and
be completed by a qualified professional.
Ensure the pipe ends male to female slide in a minimum of 1
1/2'' overlap
Connect all vent sections using a minimum of 3 sheet metal
screws on the outer pipe flue.
Plan the layout of the installation's venting run before starting
the installation.
The MAXIMUM total allowable length; Refer to Linear Power
Vent Installation.
Minimum length of straight pipe between the Fireplace and the
Power Vent is: 2 feet
Access / Service Panel, must maintain 2" clearance. If 2"
clearance is not possible Minimum 30% free air must be supplied.
Disconnect the power supply when installing and/or servicing
the fireplace or the power vent system.
CAUTION
:
When cold air enters the warmer building interior, primarily at the
air intake end, condensation may occur on the exterior of the flex
pipe. To limit this condensation, install insulation over the last
twenty feet of flex pipe. Also, by sloping the last 20'-0" feet of flex
pipe downward toward the exterior of the building, elimination of
most of the condensation problems should occur. Ensure the ter-
mination is securely fastened, and sealed to the flex pipe. Fasten
the termination to exterior of the building with water tight sealant
and the appropriate fasteners.
Specifications:
Dimensions: 34 7/8"L x 18 1/2"W. x 11 1/2"D.
Vent Size: (IN) 5"/8" (Out) 5"/8"
Motors: 1/10HP each, x 1.8A each (2) motors
Sound Level: dba
Weight: 60Lbs.
