background image

Page 8

Page 8

Page 8

Page 8

Page 8

E38-PV Gas Fireplace

Part No. XM0500

Installation

Removing and Installing

 the Door

Removing the door surround:

The door surround is held in place by two metal clips at the top, and
one magnet on each side. To remove the surround, pull the bottom
outwards and lift upwards until the slots "A" are clear of tabs "B" in
the door. You may need to use a flat screwdriver to pull the door
surround outwards. 

(See figure 13a).

Removing the door:

To install/remove the glass door simply attach/remove the five (5)
machine screws, align tabs at the bottom of the door with the slots in
the bottom door rail 

(See figure 13b).

 Ensure that a good seal is

maintained when installing the door.

Figure 13a.

  Removing or installing the door surround.

Glass door
and frame

Door surround

Tab 'B'

Slot 'A'

Magnet

Pull bottom of door
surround outwards
and upwards.

Glass door
& frame

Figure 13b.

   Removing or installing the glass door.

Removing and Installing

 the Insert

You may 

remove the insert

 to protect it from theft and damage

during construction.

1.

Remove the two machine screws (1 left & 1 right) at the top of the
insert that attach the insert to the shell.

 

See Figure12, 

Inset 1.

2.

Remove the 4 machine screws that hold the venting plate to the
insert.

3

. Remove the insert by tipping the top of the insert outward and

lifting the tabs past the slots in the bottom of the shell. 

See Inset

2.

Store the screws and clamps in a safe place to ensure that they are
not lost.

To 

re-install the insert

 simply reverse the steps above.

Figure 12.

 

E38-PV insert.

Tab

Tab

Tab

Tab

Tab

INSET 2

INSET 2

INSET 2

INSET 2

INSET 2

Front

Front

Front

Front

Front

Slot

Slot

Slot

Slot

Slot

INSET 1

INSET 1

INSET 1

INSET 1

INSET 1

Mounting

Mounting

Mounting

Mounting

Mounting
Bracket

Bracket

Bracket

Bracket

Bracket

Venting Plate

Содержание E38-PV



















Отзывы: