Montigo E38-PV Скачать руководство пользователя страница 7

Страница: 7 / 18

Page 7

E38-PV Gas Fireplace

Part No. XM0500

Installation

Installing Flex V

Installing Flex Venting

enting

IMPORTANT:

All joints must be siliconed with an approved high

temp silicone except for the termination. Apply silicone to all
joints and allow a 24 hour curing time before operating the
appliance.

2. Measure the distance between the termination and the fireplace to

determine the amount of flexible vent you will require.

3. Flexible vent sections are available in 12 foot (6' compressed)

lengths. Install the flexible vent from the fireplace to the
terimination. Flexible vent can be attached to one another using
vent connectors and may be cut to desired length.

Please note:

there should be one joint for every 12 feet of pipe.

4. Spring spacers should be installed

every three(3) feet.

Slide the

spring spacers over the 4" inner flexible vent.

(See Figure 11).

5. Support the flexible vent with plumber's strap (supplied by

installer). On horizontal runs, support the vent every three(3) feet
to prevent the vent from sagging.

6. Maximum 60 feet of vent allowed with 4 x 90° bends.

7. The flexible vent is tested for 0" clearance to combustibles.

Allowable number of 90° Bends per vent length:

Length # of 90 Bends

60 feet

4 x 90°

45 feet

4 x 90°

30 feet

5 x 90°

25 feet

5 x 90°

20 feet

6 x 90°

Example:

25 feet of flexible vent length would allow
the use of five(5) 90 degree elbows.

NOTES:

All dimension lengths for vertical or horizontal runs are

measured from center of the vent pipe.

All vent components must be sealed with high temp.

silicone.

Installation Of Standard Series Direct Vent
Components

The following venting components are available for the

E38-PV

A - Termination

MTO-3 (3" length)

MTO-3F (3" length)

PVDTK-47

B - Stucco Kits

MSR (stucco frame)

MOSR (stucco can)

BSR (brick can)

C - Solid section & elbow

MIHR-6 (72" length)

MIHR-10 (120" length)

D - Flex sections

MFL-1 (12" section)

MFL-18 (18" section)

MFL-2 (24" section)

MFL-3 (36" section)

MFL-4 (48" section)

E - Solid sections

EXT-18 (18" f/f section)

MEXT-1 (12" m/f section)

MEXT-2 (24" m/f section)

MEXT-3 (36" m/f section)

MEXT-4 (48" m/f section)

MEXT-6 (72" m/f section)

F - Elbows

MEL-90M (m/m 90° elbow)

MEL-90F (f/f 90° elbow)

MEL-90FM (f/m 90° elbow)

EEL-45 (f/m 45° elbow)

4" Inner flexible vent

7" Outer flexible vent

Spring spacer every

three(3) feet

Figure 11.

Spring spacers

Содержание E38-PV



















Результаты поиска

Содержание E38-PV

Отзывы:

Похожие инструкции для E38-PV

Бренды по названию

Популярные бренды

Montigo E38-PV, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание E38-PV

Отзывы:

Похожие инструкции для E38-PV

Бренды по названию

Популярные бренды