Montigo DelRay DR3613LI-2 Скачать руководство пользователя страница 1

Страница: 1 / 34

xg0226 - 042220

Installation & Maintenance Manual

WARNING:

FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly could result in serious injury,

death, or property damage.

— Do not store or use gasoline or other flammable vapors and

liquids in the vicinity of this or any other appliance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any

phone in your building.

• Leave the building immediately.
• Immediately call your gas supplier from a neighbour's

phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the fire

department.

— Installation and service must be performed by a qualified

installer, service agency or the gas fitter.

DelRay

INDOOR DIREcT vENT GAS FIREPLAcE

DRL3613NI

16,000 btu/hr Natural Gas or Propane Gas

DRL3613NI-2

16,000 btu/hr Natural Gas or Propane Gas

DRL4813NI

21,000 btu NG /19,000 btu Propane /hr

DRL4813NI-2

21,000 btu NG /19,000 btu Propane /hr

A barrier designed to reduce the risk of burns

from the hot viewing glass is provided with this

appliance and must be installed for the protection

of children and other at-risk individuals.

HOT GLASS

will cAuse burns.

DO NOT TOUcH

glAss until

cooled.

NEvER

Allow children

to touch glAss.

Danger

Installation and service must be performed by a qualified installer,

service agency or the gas fitter. Check local codes and read all

instructions prior to installation.

some materials used in the manufacturing process of this product can

expose you to benzene which is known in the state of california to

cause cancer and birth defects or other reproductive harm. For more

information go to www.P65warnings.ca.gov

Warning

Installer:

leave this manual with the appliance. Please refer to the

Montigo website for the most current version of the fireplace manual

consumer:

retain this manual for future reference. Please refer to the

Montigo website for the most current version of the fireplace manual

notice

Содержание DelRay DR3613LI-2



































Результаты поиска

Содержание DelRay DR3613LI-2

Отзывы:

Похожие инструкции для DelRay DR3613LI-2

Бренды по названию

Популярные бренды

Montigo DelRay DR3613LI-2, Инструкция по установке и обслуживанию

Результаты поиска

Содержание DelRay DR3613LI-2

Отзывы:

Похожие инструкции для DelRay DR3613LI-2

Бренды по названию

Популярные бренды