background image

© 2013 Monte Carlo Fan Company

8/13/2013

6

Install 3 screws to install light pan.

32

Connect plug from fan to switch

house plug. Be sure plugs connection

snap together completely. 

29

Install by twisting clockwise, add 1

screw removed step 27 to switch

housing plate. Tighten the 3 screws

securely.

28

Connect white wire from fan to white

wire from light fixture. Then plug

blue wire from fan to black wire from

light fixture.

31

Loosen the pre installed screws of

switch housing plate. Save removed

screw for use later.

Install a JD 75 watt halogen bulb, bulb in-

cluded.

Caution

: Do not replace bulb until it cools

down.   

WARNING:

Over lamping the fan will re-

sult in the fan lights shutting down until

the proper wattage of bulbs are installed.

Reset the lights by turning off the wall

switch, breaker,or by remote. Replace bulbs

with the correct wattage bulbs, turn the

power on.

33

30

Attach glass by locating dimples in

light fixture with the groves in glass

and twisting clockwise till tight.

34

Setting the reverse switch in the left hand

side will result in downward airflow and set-

ting the switch in the right hand side will re-

sult in upward airflow.

Note

: Reverse switch must be set either

completely LEFT or completely Right for fan

to function. If the reverse switch is set in the

middle position, fan will not operate. 

35

Reverse switch

Left hand side

(Forward)

Right hand side

(Reverse)

Loosen 2 screws and remove 1 screw

from motor plate. Save removed

screw for use later.

27

Содержание 5DI52XXD-L Series









Отзывы: