background image

Installation work and electrical wiring must be done b y qualified person(s) in accordance with  applicable codes and standards (ANSI/NFP A 70-

1999), including fire-rated construction.

Use this unit only in the manner intended b y the manufacurer.  If you have  any questions contact the manufacturer.

After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment -grounding conductor on one

side of the outlet box and ungrounded conductor on the other side of the outlet bo x.

Before you begin installing the fan, Switch power off at Service panel and lock service disconnecting means to prev ent power from being switched

on accidentally.  When the service disconnecting means cannot be lock ed, securely fasten a prominent warning device, such  as a tag, to the service

panel.

Be cautious! read all instructions and safet y information before installing your new fan. Review the accompanying assembly diagrams.

When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

Make sure the installation site you choose allows the fan blades to rotate without an y obstructions. Allow a minimum clearance of 7 feet from the

floor to the trailing edge of the blade.

WARNING – Risk of fire, electric shock, or personal injury , The fan in this box may be either directly supported from a structur al framing member of

a building and/or may be mounted to an outlet bo x marked acceptable for fan support of 31.8 kg. (70 lbs.) or less. Most outlet bo xes commonly

used for the support of luminaires ma y not be acceptable for fan support and ma y need to be replaced. Consult a qualified electrician if in doubt.

Do not bend blade holders during installation to motor, balancing or during cleaning.  Do not insert foreign object between rotating blades.

Attach the mounting bracket using only the hardware supplied with the outlet box.

To reduce the risk of fire or electric shock, do not use this fan with an y solid state fan speed control device, or v ariable speed control.

If this unit is to be installed o ver a tub or shower, it must be marked as appropriate for the application.

NEVER place a switch where it can be reached from a tub or shower .

The combustion airflow needed for safe oper ation of fuel-burning equipment may be affected by this unit’s operation. Follow the heating equipment

manufacturer’s guideline safety standards such as those published b y the National Fire Protection Association (NFPA), and the American Society for

Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.

Before servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting means to prev ent power from being switched on

accidentally.  When the service disconnecting means cannot be lock ed, securely fasten a prominent warning device, such  as a tag, to the service

panel.

1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

11.

12.

13.

14.

15.

Installation

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJUR Y TO PERSONS,

OBSERVE THE FOLLOWING: READ AND SAVE THESE INSTRUCTIONS

S

AFETY

T

IPS

TTO

OO

OLLSS R

REEQ

QU

UIIR

REED

D

PPh

hiilllliip

pss S

Sccrreew

wd

drriivveerr      W

Wiirree C

Cu

utttteerrss       PPlliieerrss

S

Stteep

p LLaad

dd

deerr

Before you begin installing the fan, S witch

power off at Service panel and lock service dis -

connecting means to prevent power from being

switched on accidentally.  When the service dis -

connecting means cannot be lock ed, securely

fasten a prominent warning device, such  as a

tag, to the service panel.

Warning

-Risk of fire, electric shock, or person -

al injury. The fan in this bo x may be either

directly supported from a structural framing

member of a building and/or ma y be mounted

to an outlet box marked acceptable for fan sup -

port of of 31.8 kg (70 lbs) or less. Most outlet

boxes commonly used for the support of lummi -

naires may not be acceptable for fan support

and may need to be replaced. Consult a quali -

fied electrician if in doubt. 

2

1

OUTLET BOX METHOD

Remove Safety bar from mounting bracket by

loosing screws, sliding bar to side, and lifting it

off the 2 screws.

3

Secure mounting plate directly to a joist from

the buliding structure via the two knock out

holes on the outlet bo x. Use only the appropri -

ate wood screws and w ashers included with

your fan. Caution: Wood screws must go

through into the building joist.

5

Outlet box

Mounting
Plate

Wood

Screws

BUILDING STRUCTURE METHOD

Install the mounting Plate to appro ved fan

brace and box combination use only the hard -

ware provided with the fan brace and box.

6

FAN BRACE AND BOX METHOD

Remove the 6 screws attaching the Mounting

neck the mounting plate.  Retain the 

6

 screws

for re-assembly.

4

Содержание 5CLR66XXD-L Series


















Отзывы: