MST702 3 09/16/15
Drain Daily
Regulator
Oiler
Quick Coupler
Leader
Hose
Nipple
Do Not Install
Quick Coupling
Here
Nipple
Filter
Air Supply
Whip Hose
Tools operate on a wide range of air pressures. It is required that air
pressure measures 90 psig at the tool with the trigger fully depressed
and no load applied to the tool. Higher pressure (over 90 psig; 6.2 bar)
raises performance beyond the rated capacity of the tool, which will
shorten tool life and could cause injury.
Always use clean, dry air. Dust, corrosive fumes and/or water in the air
line will cause damage to the tool. Drain the water from air lines and
compressor prior to running tool. Clean the air inlet filter screen weekly.
The recommended hookup procedure can be viewed in the above figure.
The air inlet used for connecting air supply has standard 1/4" NPT. Line
pressure should be increased to compensate for unusually long air
hoses (over 25 feet). Minimum hose diameter should be 3/8" I.D. and
fittings should have the same inside dimensions and be tightly secured.
Ensure an accessible emergency shut off valve has been installed in the
air supply line and make others aware of its location.
Lubricate the air motor daily with high quality air tool oil. If no air line
oiler is used, run 1/2 oz. of oil through the tool. The oil can be squirted
into the tool air inlet or into the hose at the nearest connection to the air
supply, then run the tool. A rust inhibitive oil is acceptable for air tools.
WARNING:
After an air tool has been lubricated, oil will discharge
through the exhaust port during the first few seconds of operation. The
exhaust port must be covered with a towel before applying air pressure
to prevent serious injury.
Always turn off the air supply, drain hose of air pressure and
detach tool from air supply before installing, removing or
adjusting any part or accessory on this tool, or before performing
any maintenance on this tool.
Bonded abrasive mounted point grinding wheels, rotary files and carbide
burrs can be mounted providing their speed rating exceeds the speed of
the Die Grinder. The shank size of the mounted accessory must match
the collet size fitted in the Die Grinder. Insert the shank of the mounted
point as far as possible into the collet and tighten the nut using the
supplied wrenches. Minimum shank gripping length must be 10mm.
After mounting a new point, start the Die Grinder under bench and run
for a few seconds. If the Die Grinder starts to vibrate when first fitting a
mounted point or during operation, immediately remove from service.
If
Die Grinder is dropped, replace bonded abrasive mounted point
grinding wheel, rotary file or carbide burr.
When using the Die Grinder, be careful not to exert excessive force which
could be hazardous and cause mounted spindle to bend or break.
NOTE: During operation, safety goggles should always be worn
to guard against flying rust and chips (users and bystanders)
.
Other factors outside the tool may cause loss of power or erratic action.
Reduced compressor output, excessive drain on the air line, moisture or
restrictions in air pipes or the use of hose connections of improper size
or poor conditions may reduce air supply. Grit or gum deposits in the
tool may cut power and may be corrected by cleaning the air strainer
and flushing out the tool with gum solvent oil or an equal mixture of
SAE #10 and kerosene. If outside conditions are in order, disconnect
tool from hose and take tool to your nearest authorized service center.
Air Supply
luBriCATiON
OpErATiON
TrOuBlESHOOTiNG
LIMITED 1 YEAR WARRANTY
MONSTER MOBILE WARRANTS TO ITS CUSTOMERS THAT THESE TOOLS ARE FREE FROM DEFECTS
IN WORKMANSHIP AND MATERIALS.
During this warranty period, if a Monster Mobile Air Tool fails to give satisfactory performance due to defective workmanship or materials,
Monster Mobile will repair or replace the tool at our option.
Other important warranty information….
This warranty does not cover damage to tools arising from alteration, abuse, misuse, damage and does not cover any repairs or replacement
made by anyone other than the authorized Monster Mobile service center. The foregoing obligation is Monster Mobile's sole liability under this or
any implied warranty, and under no circumstances shall we be liable for any incidental or consequential damages.
Note: Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not
apply to you.
Repair Procedure:
Return the tool to Power Tool Repair in Akron Ohio, transportation prepaid. Make sure to include your name, address, and
copy of proof of purchase, along with a description of the suspected defect or performance issue. If you have any questions about warranty
service, please contact your Monster Mobile distributor.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
Power Tool Repair
891 Moe Dr # H,
Akron, OH 44310
(330) 630-0022
