Monessen Hearth IDV380NV Скачать руководство пользователя страница 16

Страница: 16 / 40

57D0016

VENT INSTALLATION

MANIFOLD REMOVAL AND INSTALLATION

The manifold is shipped attached to insert. It may be removed to allow tight installation. Mani-

fold may be loosened and rotated for desired pipe location.

1. Remove brick liner and bafﬂ e.
2. Remove manifold. Place manifold

in ﬁ replace.

3. Route ﬂ ex vent through chimney

from above.

See Figure 10.

Leave

an extra 3" (914mm) at the top.

4. Attach ﬂ ex vent to manifold.

See

Figure 11.

Seal with silicone and

attach with screws.

5. Place manifold in an upright

position. Have someone pull

on the excess ﬂ ex vent.

Figure

12.

Temporarily attach ﬂ ex vent

to top of chimney. Leave some

extra slack in ﬂ ex vent.

6. Slide insert into place. Guide

the manifold over the insert

until it is fully in place.

Figure 13.

7. Remove any slack from ﬂ ex

vent. Attach manifold to insert.

Figure 13.

8. Remove any excess slack in

ﬂ ex line. Attach vent termina-

tion.

Figure 13.

Figure 12 - Pulling On

Excess Flex Vent

Figure 13 - Sliding Insert

Into Place

Manifold

Chimney

Figure 10 - Placing

Manifold Into Fireplace

Figure 11 - Attaching

Flex Vent to Manifold

Flex Vent

Extra 3"

(914mm)

Manifold

Flex Vent

Chimney

Manifold

Chimney

Excess

Flex Vent

Slack in

Flex Vent

Manifold

Bracket

Nut

Insert

Excess Slack Taken

Out of Flex Vent

Vent

Termination

Chimney

9. Replace

bafﬂ e and

brick liner.

Bracket

Nut

Содержание IDV380NV









































Результаты поиска

Содержание IDV380NV

Отзывы:

Похожие инструкции для IDV380NV

Бренды по названию

Популярные бренды

Monessen Hearth IDV380NV, Инструкция по установке и эксплуатации

Результаты поиска

Содержание IDV380NV

Отзывы:

Похожие инструкции для IDV380NV

Бренды по названию

Популярные бренды