Monessen Hearth DLX18 Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 36

Monessen Hearth DLX18 Скачать руководство пользователя страница 26

26

14D9999

14D9999

27

FOR YOUR SAFETY READ BEFORE LIGHTING

Figure 27 - Location of Piezo Ignitor and Control

Knob on Manual and Thermostat Unit

Piezo Ignitor

A.

This appliance is equipped with an ignition device which automatically lights the pilot. Do not try to light
the unit by hand.

B.

BEFORE OPERATING smell all around the appliance area for gas. Be sure to smell next to the floor be-
cause some gas is heavier than air and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS:

  •     Do not attempt to light any appliance.
  •     Do not touch any electric switch; do not use any phone in your building.
  •     Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's instructions.
  •     If you cannot reach your gas supplier, call the fire department.

C.

Use only your hand to push in, or turn the gas control knob. Never use tools. If the knob will not push in or
turn by hand, don't try to repair it. Call a qualified service technician. Force or attempted repair may result
in a fire or explosion.

D.

Do not use this appliance if any part of it has been under water. Immediately call a qualified service tech-
nician to inspect the appliance and to replace any part of the control system and any gas control that has
been under water.

OPERATING INSTRUCTIONS

Control Knob

Figure 28 - Location of Piezo Ignitor, On/Off

Switch, and Control Knob on Milli-Volt Unit

Piezo Ignitor

Hi/Low Knob

Control Knob

On/Off Switch

If you do not follow these instruction
exactly, a fire or explosion may result
causing property damage, personal
injury or loss of life.

W

ARNING

«
...
24
25
26
27
28
...
»

Содержание DLX18





































Отзывы:

Нет отзывов