Monessen Hearth DLX18 Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 36

Monessen Hearth DLX18 Скачать руководство пользователя страница 24

24

14D9999

14D9999

25

FLAME APPEARANCE

Flames from the pilot, front and rear burner should be visually checked as soon as the heater is installed.

In addition, periodically check the flames visually during operation.

CHECKING THE PILOT FLAME
The pilot flame must always be present when the heater is in operation.

It should just touch the top of the ther-

mocouple tip for natural.

See Figure 22 and 24

for correct pilot flame.

If the pilot flame does not touch the thermocouple, then the main burner cannot function reliably.

See Figure 23 and 25

for

incorrect shape of pilot flame.

MILLI-VOLT CONTROL

NOTE: For illustration purposes, natural gas and propane components are combined.

Figure 22 - Correct Appearance of Pilot Flame

Figure 23 - Incorrect Appearance of Pilot Flame

MANUAL CONTROL AND THERMOSTAT CONTROL

NOTE: For illustration purposes, natural gas and propane components are combined.

Figure 24 - Correct Appearance of Pilot Flame

Figure 25 - Incorrect Appearance of Pilot Flame

Thermocouple

for Natural

Thermocouple

for LP

Thermocouple

for LP

Thermocouple

for Natural

Thermocouple

for Natural

Thermocouple

for LP

Thermocouple

for LP

Thermocouple

for Natural

«
...
22
23
24
25
26
...
»

Содержание DLX18





































Отзывы:

Нет отзывов