Monessen Hearth DLX18 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 36

Monessen Hearth DLX18 Скачать руководство пользователя страница 17

16

14D9999

14D9999

17

��

��

Figure 13 - Damper Stop Installation.

(See WARNING at top of next page.)

FIREPLACE PREPARATION

BEFORE FULLY INSTALLING THE UNIT:

•

Turn

OFF

the gas supply to the fireplace or firebox.

•

Seal any fresh air vents and/or ash clean-out doors located on the floor or wall of the fireplace. If left unsealed, draft-

ing may cause pilot outage or sooting. Use a heat resistant sealant.

Do not seal the chimney flue damper.

INSTALLING VENTED APPLICATIONS

Manual and millivolt controlled gas logs may be installed as a vented decorative log set in compliance with ANSI Z21.60
and National Fuel Gas Code, Section 6.6 Since, the gas logs are operated with the damper open, non-combustible material
and minimum mantel requirements do not apply.

BEFORE INSTALLING THE APPLIANCE:

• Turn off gas supply to fireplace or firebox.
• Have the fireplace floor and chimney professionally cleaned to remove ashes, soot, creosote or other obstructions. Have

this cleaning performed annually after installation.

• Seal any fresh air vents or ash clean-out doors located on floor or wall of fireplace. If not, drafting may cause pilot outage

or sooting. Use a heat-resistant sealant. Do not seal chimney flue damper.

Install and operate the appliance as directed in this manual.

DAMPER STOP INSTALLATION:

A damper stop must be provided with the unit. Contact your
dealer to obtain one. The damper stop must be installed as
shown in

Figure 13

to prevent full closure of the fireplace

damper blade and provide a minimum 29 square inch flue
opening.

Before installing in a solid fuel burning
fireplace, The chimney flue and firebox
must be cleaned of soot, creosote,
ashes and loose paint by a qualified
chimney cleaner.

W

ARNING

This appliance is for installation only in a solid fuel burning fireplace (masonry fireplace
or manufactured fireplace) with a working flue and constructed of noncombustible
material. Exception: DO NOT install this applicance in a factory-built fireplace that
includes instructions stating it has not been tested or should not be used with unvented
gas logs.

W

ARNING

«
...
15
16
17
18
19
...
»

Содержание DLX18





































Отзывы:

Нет отзывов