Monessen Hearth DLX18 Скачать руководство пользователя страница 1

MODELS 

DLX18
DLX24
DLX28

Natural Gas or Propane/LPG

Control Type:

Manual, Thermostat or Milli-Volt

UNVENTED GAS LOG HEATER OR 

VENTED DECORATIVE APPLIANCE

INSTALLATION AND OPERATING INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

WARNINGS

If the information in this manual is not followed exactly, 
a fire or explosion may result causing property damage, 
personal injury or loss of life.
–    Do  not  store  or  use  gasoline  or  other  flammable 

vapors and liquids in the vicinity of this or any other 
appliance.

–    WHAT TO DO IF YOU SMELL GAS

      • Do not try to light any appliance.
      • Do not touch any electrical switch; do not use any 

phone in your building.

      • Immediately call your gas supplier from a neighbor's 

phone. Follow the gas supplier's instructions.

      • If you cannot reach your gas supplier, call the fire 

department.

–    Installation  and  service  must  be  performed  by 

a  qualified  installer,  service  agency  or  the  gas 
supplier.

This is an unvented gas-fired heater. 
It uses air (oxygen) from the room 
in which it is installed. Provisions 
for adequate combustion and 
ventilation air must be provided. See 
page 7. 

This  appliance  may  be  installed  in 
an  aftermarket,  permanently  located, 
manufactured  (mobile)  home,  where 
not prohibited by local codes.
This appliance is only for use with the 
type of gas indicated on the rating plate. 
This appliance is not convertible for use 
with other gases.

Содержание DLX18





































Отзывы: