Monacor Security TFT-900LED, Инструкция по эксплуатации

Страница: 12 / 31

6 Operation
The on-screen insertions and menu settings
described here apply to the factory-set menu
language English (to switch to another language
menu item Language , chapter 6.5.2).
6.1 Switching-on / stand-by mode
If the power indication (7) shows red after connect-
ing the power supply and if the screen remains
dark, the monitor is in the stand-by mode. To switch
on the monitor, press the button
(6), the power
indication is changed to green. To switch back to
stand-by, press the button
again.
Note: The monitor has a low power consumption even in
stand-by mode. To switch off monitor and power supply
unit completely if they are not in use for a longer period of
time, the power supply unit should be disconnected from
the mains socket to save power.
The monitor switched on reproduces picture and
sound of the last signal source selected. For the
first setting into operation the source at the HDMI
TM
input (8) is selected. In the upper right corner of the
picture the following information is shortly inserted:
– identification of the source:
– short information about the source, e. g. the
video standard (PAL or NTSC) for AV1 and AV2 ,
the resolution of the graphics card for PC .
Note: For the VGA input no information is inserted in the
upper right corner when
Auto-Adjust
(automatic picture
adjustment chapter 6.4) is displayed.
If the monitor does not receive any video signal
from the source, the screen is blue and no sound is
reproduced. Even with missing video signal, the
identification for the sources
AV1
,
AV2
and
SVIDEO is shortly inserted, but not for the sources
HDMI and PC , instead the message No-Sync
appears in the centre of the picture.
6.2 Switching over the sources
1) Press the button SOURCE (2). A list of sources
is inserted, the source presently selected is
marked.
2) Select the source with the button (2) or (3).
3) Confirm the selection with the button SELECT
(5). After switching over to the source, the iden-
tification of the source and short information are
briefly inserted (
chapter 6.1).
If the selection of a source is not confirmed, the list
is automatically deactivated when the insertion
time adjusted in the menu (menu item
Duration
chapter 6.5.2) has elapsed after the last button
has been pressed. The list can also be deactivated
with the button EXIT (1).
6.3 Adjusting the volume
Press one of the buttons VOL, (4) or (5), to
insert the adjusting scale for the volume. Then
reduce the value for the volume with the button
or increase it with the button .
The scale is automatically deactivated when the
insertion time adjusted in the menu (menu item
Duration chapter 6.5.2) has elapsed after the
last button has been pressed. The scale can also
be deactivated with the button EXIT (1).
6.4 Automatic picture adjustment
For the source PC at the VGA input (14) an auto-
matic picture adjustment can be made with the but-
ton AUTO (3). Then manual adjustments on the
menu page
FUNCTION ( chapter 6.5.3) are cor-
rected. After pressing the button, Auto-Adjust is
inserted during the adjustment.
Note: An automatic picture correction is also made each
time the monitor is switched over to the source
PC and
after switching-on, however, in these cases the message
Auto-Adjust
is not always displayed as an indication.
6.5 Adjustments in the on-screen menu
1) To call the menu, press the button MENU (1), the
first menu page is inserted.
In the toolbar at the top the menu pages are
marked as follows:
1 st page PICTURE ,
depending on the video signal:
or
2 nd page SYSTEM :
3 rd page
FUNCTION
,
only available for the source PC :
2) To select a menu page, go to the respective icon
with the button (4) or (5).
3) To select menu items on one page, use the but-
ton (2) or (3).
4) If a menu item has been selected, change its
value with the button (4) or (5) or select an
adjusting option. If only an arrow is shown
manual picture adjustment
basic adjustment
picture adjustment
AV1
or
AV2
source at the input
VIDEO 1 or VIDEO 2 (9)
SVIDEO
source at the input S-VIDEO (12)
HDMI
source at the HDMI TM input (8)
PC
source at the VGA input (14)
12
GB