Monacor AV-5810RDX, Инструкция по эксплуатации

Страница: 13 / 26

4.2.5 Connecting and aligning the antenna
Connect the supplied antenna (3) to the jack “antenna
socket” (16). For a larger range it is also possible to
connect to this jack another 5.8 GHz antenna of the
series DX-58/.. of the programme range from
MONACOR. The reception antenna must be aligned
in parallel to the transmitting antenna (also see chap-
ter 4.3.2 Channel selection). By turning the reception
antenna (3), align it vertically or horizontally:
➃
Vertical polarization Horizontal polarization
4.2.6 Power supply
For power supply a regulated power supply unit is
required with an output voltage between 7 and 30 V
and an output current of 400 mA as a minimum, e. g.
PS-1000ST from MONACOR.
In case of power supply units with variable output
voltage, adjust the voltage between 7 V and 30 V.
Connect the power supply unit via a low voltage plug
5.5/2.1 mm (outside/inside diameter) to the jack
“DC 7 - 30 V” (15). Observe the correct polarity in any
case: apply the positive pole to the inner contact of
the plug.
4.3 Making the adjustments
The AV-5810RDX has 48 programmes on which the
channel numbers and further functions can be stored
via an on-screen menu (see chapter 4.3.1). The re-
ceiver is programmed ex factory as follows:
The other functions are preprogrammed for all pro-
grammes as follows:
on the menu page
1
Name no name entered
AFC off automatic fine tuning off
Video normal video signal not inverted
AV-Rel. n.c. when receiving a video signal, the
contacts are closed
SW-Rel. n.c. with activated control channel the
contacts are closed
on menu page 2
Audio on audio reproduction activated
Signal off no signal sound activated
Auto off with switching mode activated the
programme is skipped
Hold off with switching mode activated the
dwell time adjusted in the line
“Auto” is kept
If this factory setting is sufficient, the on-screen menu
need not be called but only the corresponding pro-
gramme has to be selected with the button “P+” or
“P-” (6) [see chapter 5].
4.3.1 Settings in the on-screen menu
Switch on the receiver with the switch “power” (1).
Select the programme to be adjusted with the button
“P+” or “P-” (6). Keep the button “OK” (7) pressed for
approx. 3 seconds until the first menu page appears
on the screen. If the receiving signal is too poor or
missing, the menu is highlighted in blue colour for bet-
ter viewing.
➄
First menu page
➅
Second menu page
1) To change functions, select the corresponding
menu line with the button “P+” or “P-” (6) and
adjust it with the button “L-” or “L+” (5).
Program 1
Audio on
Signal off
Auto off
Hold off
Day 15
Month 09
Year 2006
Hour 16
Minute 44
Level
❚❚❚❚❚❚❚❚❚❚
-6-7-8
Program 1
Name ....
Freq. 5732,00 MHz
Channel 01
AFC off
Video normal
AV-Rel. n.c.
SW-Rel. n.c.
Level ❚❚❚❚❚❚❚❚❚❚ -6-7-8
audio B DIN-AV remote
control
audio A video
AV channel
switching channel
DC 7 - 30V
1 antenna 2
socket
max.
42V
0,5A
audio B DIN-AV remote
control
audio A video
AV channel
switching channel
DC 7 - 30V
1 antenna 2
socket
max.
42V
0,5A
13
ENGLISH
Programme Channel Frequency (MHz)
1 1 5732
2 2 5741
3 3 5750
4 4 5759
5 5 5768
6 6 5777
7 7 5786
8 8 5795
9 9 5804
16 16 5867
17 – 48 16 5867
10 10 5813
11 11 5822
12 12 5831
13 13 5840
14 14 5849
15 15 5858