background image

17

7.7 Applying self-levelling cement

•   Consult the manufacturer’s instruction for the type of floor covering (ceramic, linoleum, or other).  

See Section 5;

•    Completely embed the heating cable in self-levelling cement (Figure 10). It is crucial that the ENTIRE heating 

cable be embedded. No part of the heating cable must be exposed. (A small part [top] of the  
heating cable may be exposed at the surface of the self-levelling cement ONLY IF a ceramic glue is used 
afterward AND embeds that part);

•    Level the subfloor with self-levelling cement or cover the cable with a layer of cement glue when installing  

the stones or ceramics.

Do  not  turn  on  the  floor  heating  system  before  the  cement has 
completely dried. Follow manufacturer recommandations (may 
take up to 30 days, depending on the product).

3) Third insulation and resistance test
  Before embedding the heating cable in self-levelling, measure the  
  cable’s electrical and insulation resistance and record the readings  
  on line 3) Before embedding cable.

4) Forth insulation and resistance test.
  Once the cement or binder has been applied, measure the cable’s   
  electrical resistance and record the readings on line 4) After  
  embedding cable.

IMPORTANT!

     Figure 10

Содержание CAR-P series



























Отзывы: