background image

CS 150 Battery Crimping Tool

 

Doc No: ATS-638160200 

Release Date: 12-06-07 

UNCONTROLLED COPY

 

Page 3 of 21 

Revision: A 

Revision Date: 12-06-07 

 

 

Read and understand all of the instructions and safety information in this 

 Manual before operating or servicing this tool. 

 

Keep this manual available when using this tool 

Replacement manuals are available upon request at no charge  at  

www.molex.com. 

 
 

SAFETY 

ALERT 

SYMBOL 

 

This symbol is used to call your attention to hazards or unsafe practices which could result in an injury  
or property damage.  The signal word, defined below, indicates the severity of the hazard.  The message 
after the signal word provides information for preventing or avoiding the hazard. 

 

DANGER 

 

DANGER: 
Indicates an imminently hazardous situation which, if not avoided, will result in 
Death or serious injury.

 

 

WARNING

 

WARNING
Indicates a potentially hazardous situation which, if not avoided, will result in 
Death or serious injury. 

 

CAUTION

 

CAUTION: 
Indicates a potentially hazardous situation which, if not avoided, may result in 
Minor or moderate injury.  CAUTION may also be used to alert against unsafe 
practices associated with events that could lead to personal

 

injury.

 

 
 

WARNING WARNING

 

 

Electric shock hazard: 
 
This tool is not insulated.  When using this 
unit near energized electrical lines, use 
proper personal protective equipment. 
Failure to observe this warning could 
Result in severe injury or death. 

 

 
Wear eye protection when operating  
or servicing this tool. 
 
Failure to wear eye protection could  
result in serious eye injury from flying 
debris or hydraulic oil. 

WARNING WARNING

 

 

Skin injection hazard: 
 
Do not use hands to check for oil leaks. 
High pressure oil easily punctures skin 
causing serious injury, gangrene, or death. 
If injured, seek medical help immediately 
to remove oil. 

 

Pinch points: 
 
Keep hands away from the crimping 
head when crimping. 
 
Failure to observe this warning could 
Result In severe injury or death. 

 

Содержание CS 150






















Отзывы: