MOKENEYE SG01Z, Руководство пользователя

Страница: 12 / 14

12
thinner).
• Pour some appropriate thinner (water or paint
thinner) into the Canister. Screw the Canister
back into the Canister Lid. Securely tighten.
• Attach the Battery Pack again.
• Operate the Spray Gun until only clean thinner
comes out of the Nozzle.
• Unscrew the Canister and remove the Pickup
Tube. Thoroughly clean with the appropriate
thinner.
• Unscrew the Tip Collar and remove the Air Cap
and Spray Tip, then unscrew the Needle. Clean all
parts with the cleaning brush in the appropriate
cleaning solution.
• Separate the nozzle section from the sprayer
motor, see ASSEMBLE THE MOTOR HOUSING
chapter for details.
• If using water-based material, clean the nozzle
section by running water through pickup tube
inlet. If using oil-based materials, clean pickup
tube inlet with the appropriate cleaning solution.
Repeat until sprayer is completely clean.
• Dry all parts thoroughly.
• Properly dispose of cleaning solution.
• Reassembly all the parts.
• Clean the outside of the Spray Gun with a clean,
moist cloth.
MAINTENANCE
Use only mild soap and damp cloth to clean the
power unit. Never let any liquid get inside the power
unit; never immerse any part of the power unit into
a liquid.
IMPORTANT: To assure product SAFETY and
RELIABILITY, repairs, maintenance and adjustment
(other than those listed in this manual) should be
performed by authorized service centers or other
qualified service organizations, always using
identical replacement parts.
The sprayer contains a washable/reusable filter (fig.
19) . Check the filter before and after each use. If
dirty, wash with warm water and allow to air dry
before re-installing or replace if necessary.
• To check the filter, remove the filter cover by
loosening the two screws in the cover and pulling
the cover off the sprayer. Remove the filter and
inspect. Replace filter and filter cover. Snugly
tighten screws. Never operate the sprayer
without the filter in place. Debris could be sucked
in and interfere with the function of the sprayer.
Make sure unit is clean and dry before storing.
Store unit indoors in a dry location.
To avoid serious personal injury,
always remove the battery pack
from the tool when cleaning or performing any
maintenance.
When servicing, use only identical
replacement parts. Use of any
other parts could create a hazard or cause product
damage.
NOTICE: Periodically inspect the entire product for
damaged, missing, or loose parts such as screws,
nuts, bolts, caps, etc. Tighten securely all fasteners
and caps and do not operate this product until all
missing or damaged parts are replaced. Please
contact customer service or an authorized service
center for assistance.
SERVICE
Preventive maintenance performed
by unauthorized personnel may
result in misplacing of internal wires and components
which could cause serious hazard. We recommend
that all tool service be performed by a MOKENEYE
Factory Service Center or Authorized MOKENEYE
Service Station.
STORAGE
Store the tool indoors in a place that is inaccessible to
children. Keep away from corrosive agents.
TROUBLESHOOTING
Problem: Tool will not start
Probable Cause Possible Solution
Battery pack is
depleted.
Battery pack is depleted.
Tool is over-loaded. Release the trigger switch and
try again.
Tool is over-loaded. Turn off the spray gun and
cool the battery pack under
air flow.
Battery pack is not
installed properly.
Confirm that the battery is
locked and secured to the
tool.
Damaged switch. Have the switch replaced by
an Authorized MOKENEYE
Service Center or Service
Station.
Problem: Motor hums but no spraying
occurs; Or, irregular spraying
Probable Cause Possible Solution
Needle Stuck Clean Needle with thinner
Pickup Tube not in
place
Adjust Pickup Tube
Blocked Pickup Tube Clean Pickup Tube with
thinner
Blocked Spray Tip Clean Spray Tip with thinner
Loosened Tip Collar Tighten Tip Collar