MOKENEYE SG01Z, Руководство пользователя, Страница: 10 / 14

10
Battery Pack Selection:
B201505MZ(L), B202005MZ(L), B202010MZ(L),
B203005MZ(L), B204005MZ(L), B204010MZ(L).
Charger Selection:
C05MZ1US, C10MZ1US, C20M1US, C20MK1US.
NOTICE: Please refer to the battery and charger
manuals for detailed operating information.
ASSEMBLE THE MOTOR HOUSING
See Fig. 13, 14
To prevent accidental starting that could cause
serious personal injury, always remove the battery
pack from the tool when assembling parts.
To Assemble the Motor Housing:
• Align the nozzle section 90 degrees to the motor
housing and press it fully into the motor housing
(fig. 13) .
• Grasp the nozzle section, press the release button
in the direction of the arrows on the button and
twist it 90 degrees downward until the locking
pin on the nozzle section completely fits with the
groove in the motor housing (fig. 14) . When
properly connected, the two pieces will "snap"
into place.
To Disassemble the Motor Housing:
• Separate the nozzle section from the sprayer
motor by pressing the release button on the
nozzle section.
• Grasp the nozzle section and twist until it is 90
degrees to the housing, then pull straight out.
Keep pressing the release button throughout the
process.
FUEL GAUGE BATTERY PACKS
Some MOKENEYE battery packs include a fuel gauge
which consists of four green LED lights that indicate
the level of charge remaining in the battery pack.
The fuel gauge is an indication of approximate levels
of charge remaining in the battery pack according to
the following indicators:
To actuate the fuel gauge, press and hold the fuel
gauge button. A combination of the four green LED
lights will illuminate designating the level of charge
left. When the level of charge in the battery is below
the usable limit, the fuel gauge will not illuminate
and the battery will need to be recharged.
NOTICE: The fuel gauge is only an indication of the
charge left on the battery pack. It does not indicate
tool functionality and is subject to variation based on
product components, temperature and
end-user application.
For more information regarding fuel gauge battery
packs, please send e-mail to Mokeneye Customer
Service: support@mokeneye.com.
LED FUNCTIONS OF CHARGER
LED WILL BE ON TO INDICATE STATUS OF CHARGER
AND BATTERY PACK:
• LED lights up red = Fast charging mode.
• LED lights up green = Fully charged and in
maintenance charge mode.
• LED lights up green = When an under-charged
battery pack is inserted into charger, indicates hot
battery pack or that battery pack is out of normal
temperature range or deeply discharged or
defective battery pack.
• No LED on = Defective charger.
CHARGING THE BATTERY PACK
Battery packs for this tool are shipped in a low charge
condition to prevent possible problems. Therefore,
you should charge it until the green LED on the front
of the charger comes on.
CHARGING A COOL BATTERY PACK
If battery pack is within normal temperature range,
the red LED on charger will come on.
NOTICE: If the charger does not charge the battery
pack under normal circumstances, return both the
battery pack and charger to your nearest Mokeneye
Authorized Service Center for electrical check.
• Charge the battery pack only with the charger
provided.
• Make sure the power supply is normal household
voltage, 110~240 volts, 50/60 Hz, AC only.
• Connect the charger to the power supply.
• For C05MZ1US/C10MZ1US charger, insert the plug
of the charger into the charging hole of the battery
pack.
• For C20M1US/C20MK1US charger, place the
battery pack in the charger aligning raised rib on
the battery pack with the groove in the charger.
• Press down on the battery pack to be sure contacts
on the battery pack engage properly with contacts
in the charger.
• Normally the red LED on charger will come on. This
indicates the charger is in fast charging mode.
• Red LED should remain on for approximately 1 to 2
hours then the green LED will come on. Green LED
on indicates battery pack is fully charged and
charger is in maintenance charge mode.
NOTICE: The green LED will remain on until the
charger is disconnected from the power supply.
• After normal usage, a minimum of 1 hour of
charging time is required to fully recharge battery
pack.
• The battery pack and the charger will become
75-100% charged
50-75% charged
25-50% charged
<25% charged
Pack needs to be charged