background image

10

Center for electrical check.

 

TO ATTACH/DETACH BATTERY PACK

 

See Fig. 2

 

Make  sure  that  the  ON/OFF  switch  is  in  the  "OFF" 

position  when  attaching  or  detaching  the  battery 

pack.

 

To attach the battery pack:

 

Align  the  raised  rib  on  the  battery  pack  with  the 

grooves of the tool, and then slide the battery pack 

onto the tool.

 

To detach the battery pack:

 

Depress  the  battery-release  button,  located  on  the 

front of the battery pack, to release the battery pack. 

Pull the battery pack out and remove it from the tool.

 

NOTICE:

 When placing the battery pack on the tool, 

be sure that the raised rib on battery pack aligns with 

the groove inside the tool and that the latches snap 

into  place  properly.  Improper  attachment  of  the 

battery  pack  can  cause  damage  to  internal 

components.

 

ON/OFF SWITCH

 

See Fig. 3

 

Hold the tool firmly in the soft grip area and keep your 

hands away from the blade. (Fig.3)

 

To turn the tool ON, push the on/off switch forward.

 

To turn the tool OFF, pull the on/off switch backward.

 

After  tool  use,  turn  the  tool  off  to 

help  prevent  accidental  starts  and 

possible injury.

 

VARIABLE-SPEED DIAL

 

See Fig. 4

 

Your  tool  is  equipped  with  a  variable-speed  dial, 

which allows you to match the proper speed to the 

material  being  cut,  sawed,  scraped,  or  sanded, 

thereby  enhancing  the  overall  performance  of  your 

tool  and  helping  to  save  the  accessory  from  undue 

wear.

 

a.

 

The  variable-speed  dial  is  used  to  adjust  the 

oscillation rate of the accessory.

 

b.

 

Turn the dial to increase or decrease the speed.

 

c.

 

Position “1” selects the slowest speed.

 

d.

 

Position “6” selects the fastest speed.

 

e.

 

Adjust  the  accessory  speed  for  optimum 

performance.

 

NOTICE:

 Determine the optimum speed by making a 

trial cut in a scrap piece of material.

 

Adjust the speed only when the tool 

is off or when the tool is running at 

no-load  (i.e.,  accessory  is  not  in  contact  with  any 

material). Make sure to hold the tool firmly in the soft 

grip  area  with  one  hand,  keeping  the  tool  under 

control, when adjusting the speed when running at 

no-load. 

Failure to obey this caution could cause loss 

of control and result in serious personal damage.

 

BUILD-IN LED LIGHT

 

See Fig. 5

 

Your  tool  is  equipped  with  a  build-in  LED  light, 

located on the front chest of the tool. This provides 

additional light for operation in lower-light areas. 

 

The  LED  light  will  automatically  turn  on  when  the 

on/off switch is in "ON" position, and off when the 

on/off switch is in "OFF" position.

 

INSTALL AND REMOVE ACCESSORIES

 

See Fig. 6a, 6b, 6c, 6d, 7

 

 
 

 

Always turn the tool off and remove the battery 

pack before assembling parts. 

 

Wear  protective  gloves  when  changing 

accessories. 

Accessories  become  hot  after 

prolonged  use,  and  the  sharp  edges  of  the 

accessories will cause personal injury.

 

 

Check that the accessories are correctly attached. 

Incorrect  or  insecurely  attached  accessories  can 

come loose during operation and cause a hazard.

 

To install the C-type accessory

 

a.

 

Make  sure  that  the  ON/OFF  switch  is  in  the  OFF 

position and remove the battery pack.

 

b.

 

Flip  the  clamping  lever  180°  to  the  horizontal 

position to unlock the clamp mechanism. (Fig.6a)

 

c.

 

Insert  the  c-type  accessory  into  the  drive  shaft, 

making sure that all the grooves on the accessory 

align with the ribs on the drive shaft. (Fig.6b)

 

d.

 

Flip  the  clamping  lever  to  its  original  position. 

(Fig.6c)

 

To install the O-type accessory

 

a.

 

Make  sure  that  the  ON/OFF  switch  is  in  the  OFF 

position and remove the battery pack.

 

b.

 

Flip  the  clamping  lever  180°  to  the  horizontal 

position to unlock the clamp mechanism. (Fig.6a)

 

c.

 

Remove bracket lock nut counterclockwise.

 

d.

 

Fit the o-type accessory to the drive shaft, making 

sure  that  all  the  grooves  on  the  accessory  align 

with  the  ribs  on  the  drive  shaft.  Then  screw  the 

bracket lock net. (Fig.6d)

 

e.

 

Flip the clamping lever to its original position. An 

audible "click" will signal that the lever has been 

fully  engaged  to  lock  the  clamping  mechanism. 

(Fig.6c)

 

NOTICE: 

Attach  the  accessory  in  the  desired 

orientation  for  the  task  at  hand.  The  shaft  is 

configured  so  that  the  application  tool  can  be 

installed around the tool in 30

°

  increments (Fig.7). 

Do  not  attach  the  plunge-cut  blade,  flush  circular 

blade, rigid scraper blade, or carbide grout-removal 

blade so that they face backwards, as attachment in 

this position may cause serious injury.

 

 
 

Содержание OM01Z















Отзывы: