9
OPERATING INSTRUCTIONS
To reduce the risk of fire, personal injury, and
product damage due to a short circuit, never
immerse your tool, battery pack or charger in fluid
or allow a fluid to flow inside them.
Corrosive or
conductive fluids, such as seawater, certain
industrial chemicals, and bleach or bleach-
containing products, etc. can cause a short circuit.
If any parts are damaged or missing, do not
operate this product until the parts are replaced.
Use of this product with damaged or missing parts
could result in serious personal injury.
Do not attempt to modify this Oscillating Multi
Tool or create accessories not recommended for
use with this Oscillating Multi Tool.
Any such
alteration or modification is misuse and could
result in a hazardous condition leading to possible
serious injury.
To prevent accidental starting that could cause
serious personal injury, always remove the battery
pack from the Oscillating Multi Tool when
assembling parts, making adjustments, or
cleaning the tool.
This cordless chain saw must be used only with the
battery packs and chargers listed below:
Battery Park
B202005MZ(L), B202010M Z(L), B203005M Z(L)
B203010M Z(L), B204010M Z(L).
Charger
C05MZ1US, C10MZ1US, C20M1US, C20MK1US.
NOTICE:
Please refer to the battery and charger
manuals for detailed operating information.
LED FUNCTIONS OF CHARGER
LED WILL BE ON TO INDICATE STATUS OF CHARGER
AND BATTERY PACK:
•
LED lights up red = Fast charging mode.
•
LED lights up green = Fully charged and in
maintenance charge mode.
•
LED lights up green = When an under-charged
battery pack is inserted into charger, indicates hot
battery pack or that battery pack is out of normal
temperature range or deeply discharged or
defective battery pack.
•
No LED on = Defective charger.
CHARGING THE BATTERY PACK
Battery packs for this tool are shipped in a low charge
condition to prevent possible problems. Therefore,
you should charge it until the green LED on the front
of the charger comes on.
CHARGING A COOL BATTERY PACK
If battery pack is within normal temperature range,
the red LED on charger will come on.
NOTICE:
If the charger does not charge the battery
pack under normal circumstances, return both the
battery pack and charger to your nearest Mokeneye
Authorized Service Center for electrical check.
•
Charge the battery pack only with the charger
provided.
•
Make sure the power supply is normal household
voltage,
110~240 volts, 50/60 Hz, AC only.
•
Connect the charger to the power supply.
•
For C10M1US charger, insert the plug of the
charger into the charging hole of the battery pack.
•
For C20M1US/C20MK1US charger, place the
battery pack in the charger aligning raised rib on
the battery pack with the groove in the charger.
•
Press down on the battery pack to be sure
contacts on the battery pack engage properly with
contacts in the charger.
•
Normally the red LED on charger will come on. This
indicates the charger is in fast charging mode.
•
Red LED should remain on for approximately 1 to
2 hours then the green LED will come on. Green
LED on indicates battery pack is fully charged and
charger is in maintenance charge mode.
NOTICE:
The green LED will remain on until the
charger is disconnected from the power supply.
•
After normal usage, a minimum of 1 hour of
charging time is required to fully recharge battery
pack.
•
The battery pack and the charger will become
slightly warm to the touch while charging. This is
normal and does not indicate a problem.
•
Do not place the charger and battery pack in an
area of extreme heat or cold. They will work best
at normal room temperature.
NOTICE:
The charger and battery pack should be
placed in a location where the temperature is more
than 32
o
F but less than 100
o
F.
•
When batteries become fully charged, unplug the
charger from power supply and remove the
battery pack.
CHARGING A HOT BATTERY PACK
When using the tool continuously, the batteries in the
battery pack will become hot. You should let a hot
battery pack cool down for approximately 30 minutes
before attempting to recharge. When the battery
pack becomes discharged and is hot, this will cause
the green LED to come on instead of the red LED. After
30 minutes, reinsert the battery pack in the charger.
If the green LED continues to remain on, return
battery pack to your nearest Mokeneye Authorized
Service Center for checking or replacing.
NOTICE:
This situation only occurs when continuous
use of the tool causes the batteries to become hot. It
does not occur under normal circumstances. Refer to
"CHARGING A COOL BATTERY PACK"
for normal
recharging of batteries. If the charger does not
charge your battery pack under normal
circumstances, return both the battery pack and
charger to your nearest Mokeneye Authorized Service
Содержание OM01Z
Страница 14: ......
