background image

 

 

28 

 

wear protective gloves and goggles 

 

do not block charging flaps and ash pan doors 

 

perform grate readjustment using the ash pan lever 

 

use portable 24V lamps 

 

maintain order and cleanness in the boiler room 

 

maintain  good  technical  condition  of  the  boiler  and  its  related 
 

installation 

 

during  the  winter  season  ensure  that  the  heating  process  is 
 

continuous 

 

If water freezing in the installation is suspected, check whether safety 
piping  is  not  blocked  The  water  added  to  the  water  charge  in  the 
installation  shall  return  through  the  overflow  pipe  from  the  pressure 
vessel. If safety piping is blocked, the boiler must not be ignited, and 

if  it  has  been  operating,  proceed  as  in  boiler  emergency  shutdown 
procedure (see section 3.6). 

 

It is forbidden to:   
- spill water onto the grate  
- ignite the boiler using flammable liquids 

 

After  the  end  of  the  heating  season  (April 

÷

  September), pay  special 

attention  when  using  the  boiler  for  heating  the  household  hot  water 
only Boiler power will be too high relative to the absorption capacity 
of  the  boiler,  therefore  it  will  be  necessary  to  charge  less  fuel  than 
during  normal  burning  in  winter  season  and  to  monitor  the 
thermometer.   

 

If the temperature raises above 80˚C, it will be necessary to open the shut-

off valve and let the hot water flow into the central heating installation, close the 
chimney  damper  (shut  off  the  blower).  If  possible,  open  hot  water  taps  in  the 
home (e.g. in bathtub) and drain the hot water. 

 

Each  Moderator  boiler  is  equipped  with  a  stub  pipe  intended  for  safety 

valve installation. It is absolutely necessary to install the valve, additionally the 
manufacturer  recommends  installation  of  a  thermal  protection,which  would 
protect the boiler against excessive pressure rise. (Keep in mind that the thermal 
protection will activate only if the installation pressure is not lower than 2.3 bar 
and if the safety valve is installed). 

 

 

 

Содержание Unica Max 100 kW































Отзывы: