background image

 

3

 

 

 

 

 
To prevent personal injury, injury to others, and property damage, the 

safety instructions below must be followed. Incorrect operation due to 
the failure to follow the instructions will cause harm or damage

 

Special Caution 

 

This water heater is household-based usage, and it can be installed 
in every area with hot water necessity. 

 

Plug  is  not  used  for  this  water  heater;  this  water  heater  must  be 
connected directly with the power switch that comes with leakage-

protection.  Please  distinguish  the  live

 

line  (red/brown),  the  neutral 

line (blue) and the earth line (green/yellow) during installation. 

 

Do check whether the ampere (A) of the household wiring is enough 

before  the  installation,  and  particular  circuit  must  be  used  during 
installation. 

 

Before  installing  this  water  heater,  make  sure  the 

grounding

 

electrode on the socket is reliably grounded without electricity. 

 

The  hot  water  from  this  water  heater  may  cause  scald;  therefore, 
please test the temperature of the hot water before use. 

 

The  distance  between  the  installed  water  heater  and  the  water 
output should be as nearby as possible to avoid loss of heat. 

 

This  electric  instant  water  heater  may  be  damaged  if  the  water 
hardness  is  too  high.  To  ensure  the  appliance  durability,  please 

install and put it into use on condition that the local water hardness 
is less than 450mg/L (CaCO

3

). 

 

In  time  of  lightning/thunder,  switch  “Off”  the  Miniature  Circuit 

Breaker  (MCB)  in  advance  to  protect  the  water  heater  against 
possible damage. 

 

Inspect  on  the  built-in  ELCB  (once  a  month)  to  avoid  a  hazard  to 
users such as damage to property, serious injury or death. 

 

Do  cut-off  the  power  (electricity)  supply  before  any  maintenance. 
Any  maintenance  or  adjustment  towards  this  appliance  by  non-

professional is highly prohibited. 

 

The damaged power cord must be replaced with a good power cord 

provided by the manufacturer, and the replacement should be done 
by a qualified technician or engineer or professionals of the similar 
products. 

PART 1: IMPORTANT SAFETY INFORMATION 

Содержание EI 2 W


















Отзывы: