background image

 

13

 

 

 

 
 

 

This  electric  instant  water  heater  should  be  installed  at  the  place 
without  sunshine  or  rain  spray.  Please  cut  off  the  power  supply 

(electricity flow) if the water heater is not used for a long time. 

 

In order to avoid the blockage of water heater, please rinse the pipe 

with water for about 10 seconds to drain away the impurities in the 
pipe before connecting the water supply to the water heater.  

 

If  the  water  heater  has  not  been  used  for  a  long  time,  check  the 

water heater first before use. Connect the water heater with power 
supply after the water flows out stably. 

 

To avoid moisture, do not spray water to the circuit breaker or the 
heater body directly. 

 

Please cut off the power supply in the weather of thunder and rain 
to avoid damaging the water heater. 

 

If the water heater is not used for a long period of time, please cut 

off the water inlet to prolong the durability of the water heater. 

 

Check the power cord that is connected to terminals frequently to 

make  sure  that  they  are  in  well  condition,  firmly  connected,  no 
overheating case, and in a well state of 

grounding

 

Disassembly  the  shower  head  and  the  sealing  ring  first  before 

cleaning the water heater periodically. 
 

 

 

 

 
 
 

 
 

 
 
 

 
 

PART 5: MAINTENANCE 

WARNING! 

Do  cut  off  power  supply  before  maintenance  to  avoid  danger  like 
electric shock. 

NOTE 

This water heater can only be maintained and repaired by authorized 
service  technician  of 

MODENA

.  The  incorrect  installation  and  using 

method may cause serious injury or loss of property.

 

 

Содержание EI 2 W


















Отзывы: