background image

5

3

Push the tip of the roll media forward from the back of the 5DSLG&XW.

Make sure to pull it so that there is no slackening across the roll media's 

route.

When using the roll media tray

Put the roll media on the roll media tray and 

then push the tip of the roll media forward from 

the back of the machine.

Media stopper

This stops the stock shaft from spinning when 

setting in media. It is also utilized when pulling 

roll media straight out.

4

  Press the media stopper to engage it, and then pull the leading edge

out of the front of the plotter, making sure that it completely covers the 

media sensor.

Media sensors

Slide the 

media 

stopper

Media stopper

Supplement

When actually cutting, please release the lock 

from the media stopper (while pulling to the 

exterior, slide it forward).

5

  Position the media and the push rollers to correspond with the width of

the media.

When using the model with 2 push rollers

Supplement

 The media must always be positioned over

the media sensor.

See "Aligning the Push Rollers" about the

position of the push rollers.

 

The push rollers push down on either side of the media. Use the grit 

roller position guide to make sure the push rollers are set on top of the 

grit rollers.

Push roller

Push roller

Grit roller

Media

Media sensor

Grit roller position guide

7

7

  Release the lock from the media stopper (Pull the sides and slide it forward).

Release 

the media 

stopper

Media stopper

Supplement

'LUWIURPWKHÁRRUPD\VWLFNWRWKHPHGLDZKHQ

giving it slack, so please be careful.

When the set lever is up (and the media is held down by the push rollers)

and the media stopper is unlocked, pull out the roll media and give it 

slack.

Give it slack

Create the same amount of slack in the media as will be used for the 

back of the machine.

When using the roll media tray

Create the same amount of slack in the media 

as will be used for the back of the machine.

Step 1: Raise the set lever  

DQGÀ[WKHPHGLD

Step 2: Create slack.

Give it slack

Loading Sheet Media

Supplement

See "Aligning the Push Rollers" about the 

position of the push rollers.

1

Lower the media set lever to raise the push rollers.

Media sensor

Push roller

Media set lever

Содержание RapidCut 2.0


























Отзывы: