Mobeye ThermoGuard TwinLog CML2255 Скачать руководство пользователя страница 5

Attention! Very important 

 
This user manual contains important guidelines for the installation and usage of the Mobeye

® 

device  as  described  in  this  manual.  Please  read  these  thoroughly  before  you  start  using  the 
Mobeye

® 

device. 

In case of damage caused by disregarding the guidelines, the warranty becomes void.  
The user must regularly check the proper functioning of the device. The manufacturer cannot 
be  held liable  for  any  damage  or loss  caused  by any incorrect  use  or incorrect  functioning  of 
the Mobeye

® 

device. 

 

Safety guidelines 

•   The permitted ambient temperature during operation may not be exceeded (not lower than 

-10°C and not higher than 50°C). 

•   The device is intended for use in dry and clean places. 
•   Protect the device from moisture, heat and water splashing. Not intended for external use. 
•   The guidelines for the battery usage must be regarded.  
•   Do not expose the device to strong vibrations. 
•   Do not let it fall from height. 
•   Do not use in an environment where any inflammable gases, vapors or dust are present or 

could be present.  

•   Repair of the device may only be carried out by people, trained for Mobeye

®

 repair. 

•   If  the  device  must  be  repaired,  only  original replacement  components  may  be  used.  The 

use of different parts may lead to damage of the Mobeye

®

 device. 

 

Use in accordance with the regulations 

The purpose of this device in accordance with the regulations is sending SMS text messages, 
making  telephone  calls  and  sending  (log)  files.  Other  uses  are  not  permitted  and  may 
invalidate the warranty. 
 

Battery recycling 

CR123 batteries, as used in the Mobeye CML2255, are classified as non-hazardous waste and 
can be recycled. Please take empty batteries to a nearest collection point

 

 

 

Содержание ThermoGuard TwinLog CML2255





























Отзывы: