INSTALLATION & MAINTENANCE MANUAL
These instructions should be read carefully and retained after installation by the end user for future reference
and maintenance.
These instructions should be used to aid installation of the following products:
LED3xxx / LED5xxx / LED11xxx / LEDT3xxx / LEDTxxx / LEDT11xxx
SAFETY
•
This product must be installed in accordance with the latest edition of the IEE Wiring Regulations
(BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician
•
Please isolate mains prior to installation or maintenance
•
Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating of
the circuit cable, fuse, or circuit breaker
•
Please note the IP (Ingress Protection) rating of this luminaire when deciding the location for
installation
•
This product is for indoor use only
•
This product is Class III
•
This product series is IP20 rated
•
This product is dimmable with LEDDIMMER or LEDTD1* (*suitable for flat range only)
INSTALLATION
•
Provide power to the required point of installation
•
Using the clip as a template, mark the location for, and drill the fixing holes ensuring not to infringe with
any gas / water pipes or electrical cables and insert the luminaire into the clips until it locks into place.
(see Fig. 1)
Fig. 1
•
Ensuring correct polarity is observed, connect the 230V mains supply to the primary side of the 24V
constant voltage driver (LEDAD36 not supplied), Live (brown), Neutral (blue) (see Fig. 2)
Fig. 2
•
Plug the secondary side of the driver into the luminaire
•
Switch on and check for correct operation
•
Multiple fittings can be connected using connectors and link leads
Note
– The flat range of luminaires is equipped with a switch which enables each luminaire to be switched
individually.
INSTALLATION & MAINTENANCE MANUAL
These instructions should be read carefully and retained after installation by the end user for future reference
and maintenance.
These instructions should be used to aid installation of the following products:
LED3xxx / LED5xxx / LED11xxx / LEDT3xxx / LEDTxxx / LEDT11xxx
SAFETY
•
This product must be installed in accordance with the latest edition of the IEE Wiring Regulations
(BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician
•
Please isolate mains prior to installation or maintenance
•
Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating of
the circuit cable, fuse, or circuit breaker
•
Please note the IP (Ingress Protection) rating of this luminaire when deciding the location for
installation
•
This product is for indoor use only
•
This product is Class III
•
This product series is IP20 rated
•
This product is dimmable with LEDDIMMER or LEDTD1* (*suitable for flat range only)
INSTALLATION
•
Provide power to the required point of installation
•
Using the clip as a template, mark the location for, and drill the fixing holes ensuring not to infringe with
any gas / water pipes or electrical cables and insert the luminaire into the clips until it locks into place.
(see Fig. 1)
Fig. 1
•
Ensuring correct polarity is observed, connect the 230V mains supply to the primary side of the 24V
constant voltage driver (LEDAD36 not supplied), Live (brown), Neutral (blue) (see Fig. 2)
Fig. 2
•
Plug the secondary side of the driver into the luminaire
•
Switch on and check for correct operation
•
Multiple fittings can be connected using connectors and link leads
Note
– The flat range of luminaires is equipped with a switch which enables each luminaire to be switched
individually.
• Ensuring correct polarity is observed, connect the 230V mains supply to the primary side of the 24V
constant voltage driver (LEDAD36 not supplied), Live (brown), Neutral (blue) (see Fig. 2)
Fig. 1
Fig. 2
• Plug the secondary side of the driver into the luminaire
• Switch on and check for correct operation
• Multiple fittings can be connected using connectors and link leads
Note – The flat range of luminaires is equipped with a switch which enables each luminaire to be switched
individually.
ACCESSORIES
*Accessories sold separately
LEDTD1 – a touch dimmer that plugs into the flat range of luminaires and enables all further units to be
controlled by the dimmer up to a maximum of 36W
Note – this dimmer has a memory function to retain the brightness level when the mains power is switched off
• Connect the touch dimmer to the luminaire
• Connect the secondary side of the driver to the touch dimmer (see Fig. 3)
