ACCESSORIES*
*Accessories sold separately
LEDTD1
– a touch dimmer that plugs into the flat range of luminaires and enables all further units to be
controlled by the dimmer up to a maximum of 36W
Note
– this dimmer has a memory function to retain the brightness level when the mains power is switched off
•
Connect the touch dimmer to the luminaire
•
Connect the secondary side of the driver to the touch dimmer (see Fig. 3)
Fig. 3
LEDDIMMER
– suitable for both the flat and triangular ranges of luminaires and enables all further units to be
controlled by the dimmer up to a maximum of 36W
•
Connect the dimmer to the luminaire
•
Connect the secondary side of the driver to the dimmer (see Fig. 4)
Fig. 4
LEDTD2
– a plug-in power connector for the flat range of luminaires – for use with drivers that have no suitable
connector on the secondary side
•
Unscrew the cap from the top of the connector
•
Ensuring correct polarity is observed connect the secondary side of the driver into the power connector
using suitable 2-core flex (see Fig. 5)
•
Replace the cap and secure with the two screws
•
Connect the power connector to the luminaire
Fig. 5
WARNING
This luminaire must be disconnected from the circuit if subjected to any high voltage or insulation resistance
testing. Irreparable damage will occur if this instruction is not followed.
GENERAL
Fig. 3
LEDDIMMER – suitable for both the flat and triangular ranges of luminaires and enables all further units to be
controlled by the dimmer up to a maximum of 36W
• Connect the dimmer to the luminaire
• Connect the secondary side of the driver to the dimmer (see Fig. 4)
ACCESSORIES*
*Accessories sold separately
LEDTD1
– a touch dimmer that plugs into the flat range of luminaires and enables all further units to be
controlled by the dimmer up to a maximum of 36W
Note
– this dimmer has a memory function to retain the brightness level when the mains power is switched off
•
Connect the touch dimmer to the luminaire
•
Connect the secondary side of the driver to the touch dimmer (see Fig. 3)
Fig. 3
LEDDIMMER
– suitable for both the flat and triangular ranges of luminaires and enables all further units to be
controlled by the dimmer up to a maximum of 36W
•
Connect the dimmer to the luminaire
•
Connect the secondary side of the driver to the dimmer (see Fig. 4)
Fig. 4
LEDTD2
– a plug-in power connector for the flat range of luminaires – for use with drivers that have no suitable
connector on the secondary side
•
Unscrew the cap from the top of the connector
•
Ensuring correct polarity is observed connect the secondary side of the driver into the power connector
using suitable 2-core flex (see Fig. 5)
•
Replace the cap and secure with the two screws
•
Connect the power connector to the luminaire
Fig. 5
WARNING
This luminaire must be disconnected from the circuit if subjected to any high voltage or insulation resistance
testing. Irreparable damage will occur if this instruction is not followed.
GENERAL
LEDTD2 – a plug-in power connector for the flat range of luminaires – for use with drivers that have no
suitable connector on the secondary side
• Unscrew the cap from the top of the connector
• Ensuring correct polarity is observed connect the secondary side of the driver into the power connector using
suitable 2-core flex (see Fig. 5)
• Replace the cap and secure with the two screws
• Connect the power connector to the luminaire
Fig. 4
ACCESSORIES*
*Accessories sold separately
LEDTD1
– a touch dimmer that plugs into the flat range of luminaires and enables all further units to be
controlled by the dimmer up to a maximum of 36W
Note
– this dimmer has a memory function to retain the brightness level when the mains power is switched off
•
Connect the touch dimmer to the luminaire
•
Connect the secondary side of the driver to the touch dimmer (see Fig. 3)
Fig. 3
LEDDIMMER
– suitable for both the flat and triangular ranges of luminaires and enables all further units to be
controlled by the dimmer up to a maximum of 36W
•
Connect the dimmer to the luminaire
•
Connect the secondary side of the driver to the dimmer (see Fig. 4)
Fig. 4
LEDTD2
– a plug-in power connector for the flat range of luminaires – for use with drivers that have no suitable
connector on the secondary side
•
Unscrew the cap from the top of the connector
•
Ensuring correct polarity is observed connect the secondary side of the driver into the power connector
using suitable 2-core flex (see Fig. 5)
•
Replace the cap and secure with the two screws
•
Connect the power connector to the luminaire
Fig. 5
WARNING
This luminaire must be disconnected from the circuit if subjected to any high voltage or insulation resistance
testing. Irreparable damage will occur if this instruction is not followed.
GENERAL
Fig. 5
