MKS Cirrus2 Скачать руководство пользователя | Manualshive

Страница: 20 / 54

background image

MKS Instruments UK Ltd

Cirrus2 Hardware Manual – SP101017.100 June 2011

20

Directly connecting to the Cirrus2

If your PC or MAC is not part of a network, you may choose to connect the Cirrus2 directly to the Ethernet port or a local
hub. The following section describes what is required to get your unit up and running.

As stated earlier, the Cirrus2 is configured to use Auto-IP by default, all that is left to do is to ensure your PC or MAC is
configured the same way.

Connect the Cirrus2 to your PC, MAC or hub with a standard Cat5 STP cable (there is no need to use a dedicated cross-
over cable) and power on the Cirrus2

Next you need to check if your PC or MAC is configured for Auto-IP; most are by default.

Windows PC
Start / Connect To / Show All Connections
Click once on the connection hosting the Cirrus2
Note the information displayed in the Task Pane

If the text

“Automatic Private Address”

is displayed, then the PC is ready to begin

communications with the Cirrus2 unit.

If the text

“Obtaining an IP address”

is displayed, then please wait a few moments for

the sequence to complete.

If any other text is displayed, then you will need to make changes to the way your PC
obtains IP addresses.

MAC

Apple Menu / System Preferences / Network
Ethernet / Configure
The option “

Using DHCP

” or “

Using Auto-IP

” should be displayed.

If your PC or MAC is not configured for Auto-IP, you can make the following changes to enable the function. You will
need to have Administrative privileges.

«
...
18
19
20
21
22
...
»

Содержание Cirrus2























































Отзывы:

Нет отзывов

Похожие инструкции для Cirrus2

Бренд: Zempire Страницы: 2

Бренд: Kärcher Страницы: 88

Бренд: ABB Страницы: 4

TOTAL KNEE 1900

Бренд: Össur Страницы: 58

Бренд: Ebyte Страницы: 7

Бренд: popular Страницы: 27

Бренд: Ignis Pixel Страницы: 4

Deep Root Planter 1.8m

Бренд: Zest 4 Leisure Страницы: 5

Бренд: Faro Страницы: 161

Бренд: Hanskamp Страницы: 22

ALFW-6LU-5KBZ Series

Бренд: Hubbell Страницы: 2

Бренд: SIMES Страницы: 8

Giotto spot 400

Бренд: SGM Страницы: 33

Бренд: Kramer Страницы: 16

Z100-M618.03 S5V

Бренд: Jäger Страницы: 40

Бренд: Waters Страницы: 236

Бренд: NightBalance Страницы: 1

Бренд: Sygonix Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды