manualshive.com logo in svg

MKS Baratron 127A, Инструкция по эксплуатации, Страница: 27 / 38

Поделиться
Скачать
MKS Baratron 127A Скачать руководство пользователя страница 27

Chapter Four:  Operation

How To Zero the Type 127/128 Transducer

19

Chapter Four:  Operation

How To Zero the Type 127/128 Transducer

You must zero the transducer initially when you install it into your system and periodically
thereafter.  The zero must be set by adjusting the zero potentiometer.

Note

Make sure that the unit is fully stabilized before attempting to adjust the
zero.

1. Pump down the unit, with power on, to a pressure less than the resolution (0.01% F.S.)

for approximately two to four hours (eight hours are required for the 0.1 Torr range).

Table 3, page 19, lists the maximum pressure for each full scale range.

2. Adjust the zero by turning the Zero potentiometer, located on the top of the unit.

Refer to Figure 5, page 15, for the location of the Zero pot.

The zero adjustment may also be made at the front panel of an MKS supplied readout/power
supply unit, if used.

Maximum Pressure Reading for Zero Adjustment

Full Scale Range

Maximum Pressure for Zero Adjustment

0.1 Torr

5 x 10

-6 

Torr

1 Torr

5 x 10

-5 

Torr

2 Torr

1 x 10

-4 

Torr

10 Torr

5 x 10

-4 

Torr

100 Torr

5 x 10

-3 

Torr

1000 Torr

5 x 10

-2 

Torr

5000 Torr

2.5 x 10

-1 

Torr

10,000 Torr

5 x 10

-1 

Torr

15,000 Torr

7.5 x 10

-1 

Torr

20,000 Torr

1 Torr

25,000 Torr

1.25 Torr

Table 3:  Maximum Pressure Reading for Zero Adjustment

Содержание Baratron 127A







































Отзывы:

Нет отзывов