MKS Baratron 127A Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 38

MKS Baratron 127A Скачать руководство пользователя страница 15

Chapter One: General Information

Customer Support

7

Customer Support

Standard maintenance and repair services are available at all of our regional MKS Calibration
and Service Centers, listed on the back cover. In addition, MKS accepts the instruments of other
manufacturers for recalibration using the Primary and Transfer Standard calibration equipment
located at all of our regional service centers. Should any difficulties arise in the use of your Type
127/128 instrument, or to obtain information about companion products MKS offers, contact any
authorized MKS Calibration and Service Center. If it is necessary to return the instrument to
MKS, please obtain an ERA Number (Equipment Return Authorization Number) from the MKS
Calibration and Service Center before shipping. The ERA Number expedites handling and
ensures proper servicing of your instrument.

Please refer to the inside of the back cover of this manual for a list of MKS Calibration and
Service Centers.

Warning

All returns to MKS Instruments must be free of harmful,
corrosive, radioactive, or toxic materials.

«
...
13
14
15
16
17
...
»

Содержание Baratron 127A







































Отзывы:

Нет отзывов