background image

Ax34601a_e_A5.doc / Feb-06 

 

Page 9 / 20 

 

4.

 

How to Operate the Front Keys 

All settings are done by means of two front keys. A third key on the utmost right side of the 
panel is reserved for special key operations, but not in use with standard AX346 units. 

 

 

ENTER key: scrolls through the menu headlines. 

 

 

SET key: selects the actual menu and allows to choose the desired setting or to adjust 

the desired numeric value of the actual parameter. 

 

 

ENTER key: confirms and stores the actual parameter choice and changes over to the 
next menu item. 

 

 

Key reserved for spezial operations (not in use with standard AX346 units) 

 

 

To start the menu dialogue, please keep ENTER down for at least 3 seconds. 

 

With numerical entries, at first the lowest digit will blink. When keeping the SET key down, the 
highlighted digit will scroll in a continuous loop from 0 … 9 … 0 … 9. When you release the 

SET key, the actual digit will remain and the next digit will be highlighted (blink). This 
procedure allows to set all digits to the desired values. After the most significant digit has been 
set, the low order digit will blink again and you can do corrections if necessary. With signed 

parameters, the high order digit will only scroll between the values “0” (positive) and “-“ 
(negative) To store the actual setting, press the ENTER key, which will also automatically scroll 
forward the menu. 

 

The unit changes from programming mode to normal operation when you keep down the ENTER 

key again for at least 3 seconds. 

 

Furthermore a “time-out” function will automatically conclude every menu level, when for a 
break period of 10 seconds no key has been touched. In this case, any entry which has not been 
confirmed by ENTER yet would remain unconsidered. 

 

At any time it is possible to Reset all parameters to the Factory Default Settings 

 

To do this, power the unit down, and keep the ENTER key down while you power the unit up 

again. This will set the unit to the factory default state. See the parameter default values from 
the parameter list at the end of this manual. 
 

«

™

)

«

Содержание AX346





















Отзывы: