background image

Ax34601a_e_A5.doc / Feb-06 

 

Page 5 / 20 

 

2.

 

Electrical Connections 

 

 
 
 

 
 
 

 
 
 

 
 
 

 
 
 
*) This grounding terminal is internally connected to the GND potential. Grounding of this 

terminal is not necessary, neither for safety nor for EMC reasons. With some applications 
however it may be desirable to connect the measuring GND to another ground or earth 
potential. 

Please note that earthing of this terminal will tie to earth all internal analogue and digital GND 
potentials. Multiple earthing should be avoided (e.g. if the minus pole of your DC power supply 
should already be earthed externally) 

 

2.1.

 

Power Supply 

Terminals 1 and 2 provide DC supply from a 17 to 30 volts DC power unit. The current 

consumption depends on the level of the input voltage and is typically 130 mA with 17 volts 
and 80 mA with 30 volts (sensor current taken from the aux. output not included). 
Terminals 0 VAC, 115 VAC and 230 VAC provide supply of the unit directly from the mains. The 
total AC power rating is 7.5 VA. 

2.2.

 

Auxiliary Power Output 

Terminal 7 provides a 24 volts DC output (max. 100 mA) for supply of transducers or sensors. 
This output is available with AC power supply and DC power supply as well. 

1

GN

D

 ( 0

V )

2

+17

...

30

 V

CD

3 4 5 6 7

8 9 10

GN

D

230

 V

AC

115

 V

AC

0 V

AC

In

pu

t A

In

put

 B

GN

D a

na

l.

+2

4V

 D

C

opt

io

na

l, 

se

e*

)

GN

D

 ( 0

V )

GN

D a

na

l.

+/

- 1

V

0 /

 4 -

 20

 m

A

DC

 po

w

er

 s

uppl

y

In

pu

ts

+/

- 10

 V

 or

0 /

 4 

- 20 

m

A

au

x.

 p

ow

er

ou

tp

ut

An

al

og

ue out

put

AC

 po

w

er

 s

uppl

y

Содержание AX346





















Отзывы: