MKS 252A-1-VPO Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 55

MKS 252A-1-VPO Скачать руководство пользователя страница 8

Safety Procedures and Precautions

1

Safety Procedures and Precautions

DO NOT SUBSTITUTE PARTS OR MODIFY INSTRUMENT

Do not install substitute parts or perform any unauthorized modification to the instrument.
Return the instrument to an MKS Calibration and Service Center for service and repair to ensure
that all safety features are maintained.

SERVICE BY QUALIFIED PERSONNEL ONLY

Operating personnel must not remove instrument covers. Component replacement and internal
adjustments must be made by qualified service personnel only.

DO NOT SERVICE OR ADJUST ALONE

Do not attempt internal service or adjustment unless another person capable of rendering first aid
and resuscitation, is present.

GROUNDING THE PRODUCT

This product is grounded through the grounding conductor of the power cord. To avoid electrical
shock, plug the power cord into a properly wired receptacle before connecting it to the product
input or output terminals. A protective ground connection by way of the grounding conductor in
the power cord is essential for safe operation.

DANGER ARISING FROM LOSS OF GROUND

Upon loss of the protective-ground connection, all accessible conductive parts (including knobs
and controls that may appear to be insulating) can render an electrical shock.

GROUND AND USE PROPER ELECTRICAL FITTINGS

Dangerous voltages are contained within this instrument. All electrical fittings must be of the
type specified, and in good condition. All electrical fittings must be properly connected and
grounded.

USE THE PROPER POWER CORD

Use only the power cord and connector specified for your product.
Use only a cord in good condition.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

«
...
6
7
8
9
10
...
»

Содержание 252A-1-VPO
























































Отзывы:

Нет отзывов