manualshive.com logo in svg

MKS 252A-1-VPO, Руководство пользователя, Страница: 4 / 55

Поделиться
Скачать
MKS 252A-1-VPO Скачать руководство пользователя страница 4

Table of Contents

iii

Table of Contents

Safety Procedures and Precautions.......................................................................................... 1

Chapter One:  General Information......................................................................................... 5

Introduction ............................................................................................................... 5

How This Manual is Organized.................................................................................. 7

Customer Support ...................................................................................................... 7

Chapter Two:  Installation ...................................................................................................... 9

How To Unpack the Type 252 Unit............................................................................ 9

Unpacking Checklist ..................................................................................... 9

Setup ......................................................................................................................... 11

System Design .............................................................................................. 11

Power and Fuse Requirements....................................................................... 11

Mounting Instructions ................................................................................... 12

Interconnections ............................................................................................ 12

Cables ........................................................................................................... 14

Chapter Three:  Overview....................................................................................................... 19

General Information................................................................................................... 19

Stepping Drive Motor ................................................................................................ 20

Front Panel Controls .................................................................................................. 21

Rear Panel Controls ................................................................................................... 23

Chapter Four:  Operation ........................................................................................................ 25

How To Setup the Controller ..................................................................................... 25

How To Tune-Up the Controller ................................................................................ 26

How To Use the Normal/Reverse Switch ................................................................... 27

How To Use External Control .................................................................................... 27

Advisory ....................................................................................................... 28

How To Use the Valve Position Option...................................................................... 29

Interconnections ............................................................................................ 29

How To Use the Multiple Set Point Option ................................................................ 31

Settings ......................................................................................................... 31

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание 252A-1-VPO
























































Отзывы:

Нет отзывов