manualshive.com logo in svg

MKS 252A-1-VPO, Руководство пользователя, Страница: 6 / 55

Поделиться
Скачать
MKS 252A-1-VPO Скачать руководство пользователя страница 6

List of Figures

List of Tables

v

List of Figures

Figure 1:  Standard Pressure Control Setup................................................................................ 13

Figure 2:  253 Valve Connected in Parallel with an Isolation Valve ........................................... 13

Figure 3:  Front Panel Controls.................................................................................................. 21

Figure 4:  Rear Panel Controls................................................................................................... 23

Figure 5:  Process Limit Set Point Control ................................................................................. 33

List of Tables

Table 1:  Valve Connector Pinout ..............................................................................................15

Table 2:  Transducer Connector Pinout ......................................................................................16

Table 3:  Interface Connector Pinout..........................................................................................17

Table 4:  Four-Step Sequence ....................................................................................................20

Table 5:  Valve Position Option Pinout ......................................................................................30

Table 6:  Multiple Set Point Option Pinout ................................................................................32

Table 7:  Process Limit Option Pinout .......................................................................................34

Table 8:  Test Point Voltages.....................................................................................................39

Table 9:  Troubleshooting Chart ................................................................................................41

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание 252A-1-VPO
























































Отзывы:

Нет отзывов