MK Diamond Products MK-4018HY Скачать руководство пользователя страница 8

Страница: 8 / 32

MK-4000 SERIES

SAFETY

ON / OFF

• CAUTION must be observed while servicing the machine. Rotating parts can cause injury if contacted. Have

all service performed by competent service personnel.

• Operate this machine only in well ventilated areas. ALWAYS ensure that the machine is on level ground

before using.

• NEVER operate this machine in an explosive atmosphere.

• Establish a training program and give a copy of this manual to operators of this equipment. If you need extra

copies, call TOLL-FREE (800) 421-5830.

For complete safey information, refer to ANSI Safety Code B7.1 available through the American National Standards
Institute.

• ALWAYS keep area around the machine clear of obstructions and clear the work area of

unnecessary people. Keep all body parts away from the blade and all other moving parts.

• Before starting the machine, check that all guards are in position and correctly fitted.

NEVER allow blade exposure from the guard to be more than 180 degrees. DO NOT

operate this machine with any guard removed.

• Inspect the blade, flanges and shafts for damage before installing the blade. NEVER use damaged or worn

blade flanges.

• The blade shaft flanges must be of proper diameter for the size blade being used.

• Inspect the blade, flanges and size shown for each blade size. DO NOT exceed maximum blade speed

shown, as excessive speed could result in blade breakage. Use

ONLY blades marked with a maximum op-

erating speed greater than the blade shaft speed. Verify speed and saw drive configuration by checking blade
shaft RPM and pulley diameters and blade flange diameters.

• Use the correct blade for the type of work being done. Use only reinforced abrasive blades or steel center

diamond blades and flanges supplied with the saw or manufactured for use on concrete saws.

DO NOT use

carbide-tipped blades. Check with the blade manufacturer if you do not know if blade is correct.

• Make sure the blade and flanges are clean and free of dirt and debris before mounting the blade on the saw.

Verify the blade arbor hole matches the machine spindle before mounting the blade.

ALWAYS mount the

blade solidly and firmly. Wrench tighten the arbor nut.

SAW BLADE SAFETY

• NEVER leave the machine unattended. Turn off machine when unattended. Know how to stop the

machine quickly in case of emergency.

• NEVER try to stop a moving blade with your hand.

• NEVER use a wet blade without adequate water supply to the blade.

Содержание MK-4018HY

































Результаты поиска

Содержание MK-4018HY

Отзывы:

Бренды по названию

Популярные бренды

MK Diamond Products MK-4018HY, Руководство оператора

Результаты поиска

Содержание MK-4018HY

Отзывы:

Бренды по названию

Популярные бренды