MK Diamond Products MK-4018HY Скачать руководство пользователя страница 16

Страница: 16 / 32

MK-4000 SERIES

PRODUCT SPECIFICATIONS

INSTRUCTIONS FOR CHANGING BLADE SPEED

WARNING

Do not exceed blade shaft speed shown for each blade size. Excessive blade speed could result in blade failure
and serious personal injury.

NOTICE

Changing Blade Guard size

MUST be accompanied by changing Pulleys to achieve the correct blade speed.

NOTICE

As shown on the chart, some blade guards accept more than one size blade.

BLADE GUARDS AND BLADE SIZES

BLADE GUARD

BLADE SIZE THAT CAN BE

USED WITH BLADE GUARD

18"

14” up to 18”

24"

18” up to 24”

30"

24" up to 30"

36"

30" up to 36"

Kit

Size

P/N for

Includes

Blade Shaft Speed

(Engine RPM = 3000)

Blade

Speed

(FPM)

18”

167659-18HY

167659-18KB

18” Blade Guard Assembly

4” Flange Set

3.2” Engine Pulley

4.12” Blade Shaft Pulley

7 3VX425 V-Belts

2300 RPM

14”= 8550
16”= 9800
18” = 11000

24”

167659-24HY

167659-24KB

24” Blade Guard Assembly

5” Flange Set

2.8” Engine Pulley

4.12” Blade Shaft Pulley

7 3VX425 V-Belts

2000 RPM

18” = 9600
20” = 10700
22” = 11750
24” = 12800

30”

167659-30HY

167659-30KB

30” Blade Guard Assembly

5” Flange Set

2.8” Engine Pulley

4.75” Blade Shaft Pulley

7 3VX425 V-Belts

1750 RPM

24” = 11100
26” = 12000
28” = 13000
30” = 13900

36”

167659-36HY

167659-36KB

36” Blade Guard Assembly

6” Flange Set

2.8” Engine Pulley

5.75” Blade Shaft Pulley

7 3VX450 V-Belts

36” Frame Corner

1450 RPM

30” = 11500
32” = 12250
34” = 13000
36” = 13750

Содержание MK-4018HY

































Результаты поиска

Содержание MK-4018HY

Отзывы:

Бренды по названию

Популярные бренды

MK Diamond Products MK-4018HY, Руководство оператора

Результаты поиска

Содержание MK-4018HY

Отзывы:

Бренды по названию

Популярные бренды