background image

45

Check the system as per the following procedure if the zero/span adjustment would not complete.

Item

Problem

Disposal

Input signal

The contact signal 
and the analog volt-
age signal are not 
input properly.

• Compare the ON/OFF status of the input contact signal with the sta-

tus shown on the monitor screen.  In addition, check the input contact 
for poor contact.  If the input signal is properly turned ON and OFF 
but the ON/OFF status is not displayed on the monitor, the LE-
40MTA-E tension controller is defective.

• Compare the voltage of the analog input terminal with the voltage val-

ue displayed on the monitor.  Also check that noise is not influencing 
the input line.

Others

Material gets loose 
during acceleration 
or deceleration.

• The material tends to get loose if the acceleration/deceleration time    is 

too short or the material inertia is too high.  Use gain 1 or gain 2 to   

compensate the inertia during acceleration and deceleration.

Material is displaced 
or gets too tight dur-
ing winding.

• The taper control is recommended.

Item

Problem

Disposal

Tension 

detector

Zero adjustment is 
not possible.

Check the wiring in 
accordance with 
page 5.

• If the voltage between the terminals [RED] and [BLK] is not approxi-

mately 5.0 VDC, remove the wiring of this terminal and measure     

the voltage. If the specified  voltage is not obtained, the LE-40MTA-

E is defective.

If the specified voltage is obtained, the external wiring or tension de-

tector is defective.                 

• Remove the wiring in the tension detector.     

 Short-circuit the terminals [WHR] and [GRR] as well as the terminals 

[WHL] and [GRL] . If zero adjustment is not possible still, the LE-

40MTA-E is defective.                                  

• Connect the terminals [RED] and [BLK] exclusively to the tension de-

tec  tor. If the voltage between the white and green cables in the ten-

sion detec  tor is 120 mVDC (150mV DC x 0.8)or less with which the 

current is not   applied in the material and zero adjustment is not pos-

sible, the LE-  40MTA-E is defective. If the measured voltage ex-

ceeds 120mV, the tension   detector selected is not appropriate .

  (The tare weight is 80% or more of the rated load.)

Span adjustment is 
not possible.

Check the wiring in 
accordance with 
page 5.

• Perform zero adjustment at first. Connect the  terminals [RED] and 

[BLK] exclusively to the tension detector. Measure the voltage be    

tween the white and green cables in the tension detector.                                     

• When span adjustment is not possible even if the difference between 

the voltage measured when the material tension is set to 0 and the 

voltage measured when the material tension is set to full scale value 

is 30mV (150mVDC x 0.2) or more, the LE-40MTA-E is defective .  

• When the difference in voltage is less than 30mV, the tension load ap-

plied on the tension detector is insufficient and the tension detector 

selected is not appropriate. Even if the span adjustment is normally 

completed, the tension detection error increases. 

  Use a tension detector having a less rated load.    

• If the load is changed while the span is adjusted, adjustment may be-

come disabled .

Содержание LE-40MTA-E



























































Отзывы: