Mitsubishi LE-40MTA-E Скачать руководство пользователя страница 48

Страница: 48 / 58

10.4 Unintended operation

Check the abnormality of the major components during trial operation and adjustment and during actual op-
eration using the following procedure.

Item

Problem

Disposal

Power
supply

When the POWER
switch is turned ON,
the POWER LED is
not lit.

• Make sure the supply voltage between the terminals [PSL] and [PSN] is

100 to 240VAC (+10% to -15%), 50/60 Hz. If this value is not correct,

perform the correct wiring.

• The fuse may be melted by insertion of foreign objects or abnormal loads.

If simply replacing the fuse may not solve the problem. Contact our ser-

vice department.

Tension
display
and
abnormal
tension

On the display, the
tension value or the
unit of the tension
flashes.

• The tension signal from the tension detector is too high. The applied

load may exceed the rated load of the tension detector. Lower the ten-

sion set value.

• Check the rated load of the tension detector. If no problem is detected,

increase the full-scale tension value. (After changing the full-scale ten-

sion value, be sure to tune the zero point and the span.)

When restarting after
stopping the mate-
rial, the tension read-
ing goes beyond the
scale from the begin-
ning.

• Turn ON or OFF the [MC1] input signal depending on the run/stop status

of the machine . If the [MC1] input signal is kept at on status, restarting

operation may send out the maximum control output, and an extremely

high tension may be applied.

• When stopping the machine, if the turning-OFF timing of the [MC1] input

signal is delayed, the control output may be extremely increased, and

an extremely high tension may be applied at starting operation. To pre-

vent this problem, be sure to turn OFF the [MC1] input signal when

stopping the machine.

The output increases
while the machine
halts.

• The [MC1] input signal may not be turned OFF.

• While the machine is stopped, be sure to turn off the [MC1] input signal.

After replacement of
the material, an
extremely high or low
tension is applied.

• Check that the output set for the OFF status of the [RUN] input signal is

optimum for the reel diameter of the replaced material.

• Reset the stall memory.

Fluctuating tension
control

• Check whether similar fluctuations occurs during manual operation.

• Fluctiations during manual operatinon is generally caused by changes in

tension as a result of machine vibration ,mechanical loss,etc. In this

case please check the machine.

• If fluctuations do not occur during manual operation, this is generally

caused by high control gain set by the LE-40MTA-E tension controller.

In this case, please adjust the control gain factor refer to Sec. 7.5.

Actuator

Output cannot be
obtained in the man-
ual mode.

• Make sure that the OUTPUT ON/OFF switch is turned on.

• When 0 to 24 V output is obtained between the terminals [P] and [N] by

the manual torque setting, check the wiring to the powder clutch/brake.

When no abnormality is detected , the clutch/brake is defective or se

lected inappropriately.

• If the output voltage is not obtained in the no-load condition when the

power is changed from off to on ,the LE-40MTA-E is defective.

If the short-circuit protection function between the terminals [P] and [N]

is actuated, the unit becomes the normal condition when the wiring is

corrected and the power is turned on again.

• If 0

5V output is not obtained between the terminals[SA] and [SN] and

the terminals [NRO] and [AOC], remove the external load (1k

Ω

or more)

and check whether 0

5V is obtained.

• If 4

20mA output is not obtained between the terminals [EAP] and

[EAN] , remove the E/P regulator (470

Ω

or less),connect the ammeter

between the terminals [EAP] and [EAN] , then check whether 4

20mA

output is obtained.

• While the memory cassette is attached, the control output is not gener

ated.

Содержание LE-40MTA-E



























































Результаты поиска

Содержание LE-40MTA-E

Отзывы:

Похожие инструкции для LE-40MTA-E

Бренды по названию

Популярные бренды

Mitsubishi LE-40MTA-E, Инструкция по эксплуатации

Результаты поиска

Содержание LE-40MTA-E

Отзывы:

Похожие инструкции для LE-40MTA-E

Бренды по названию

Популярные бренды