9
Fan speed: 3 stages
Display:
3.4. Fan speed adjustment
To change fan speed
Every time you press the FAN button once, it switches from the low-speed to
high-speed settings successively.
Note:
● In the following cases, the actual fan speed generated by the unit will
differ from the speed shown the remote controller display.
1. When the unit is in STAND BY or DEFROST states.
2. When the temperature of the heat exchanger is low in the heating
mode. (e.g. immediately after heating operation starts)
3. In HEAT mode, when room temperature is higher than the
temperature setting.
4. When the heater control mode is the factory setting and the heater is
on, the fan will operate at high speed.
* Every time the fan speed adjustment button is pressed once, the fan speed is
changed.
* This setting can be adjusted only with MA remote controller.
– 8 –
GB
Preset temperature range is as follows.
*1 The preset temperatures for cooling and heating for AUTO (dual set point) mode will be used for those for
COOL and HEAT mode.
*2 The preset temperatures for cooling and heating can be set under the following conditions.
• The cooling preset temperature is greater than the heating preset temperature.
• The difference between the cooling and heating preset temperatures is equal or greater than the minimum
temperature difference that varies depending on the indoor unit model to be connected.
Fan speed
ON
Vane
ON
Pressing the
button will change the fan speed in the following order.
* The settable fan speed varies depending on the indoor unit model to be connected.
* If the unit has no fan setting function, the fan speed cannot be set.
In this case, the fan icon blinks when the
button is pressed.
Pressing the
button will switch the vane directions.
* The settable vane direction varies depending on the indoor unit model to be connected.
* If the unit has no vane function, the vane direction cannot be set.
In this case, the vane icon blinks when the
button is pressed.
Operation mode
Preset temperature range
COOL
67 - 87 (95)°F/19 - 30 (35)°C
HEAT
63 (40) - 83°F/17 (5) - 28°C
AUTO (single set point) 67 - 83°F/19 - 28°C
AUTO (dual set point)
[COOL] Preset temperature range for COOL mode.
[HEAT] Preset temperature range for HEAT mode. *1, *2
SETBACK
[COOL] Preset temperature range for COOL mode.
[HEAT] Preset temperature range for HEAT mode. *2
FAN
Unsettable
FAN
AUTO
FAN
VANE
AUTO
Setting 1
Setting 2
Setting 3
Setting 4
Setting 5
Swing
VANE
4. The smart way to use
Even minimal steps to care for your air conditioner can help make its use
far more effective in terms of air-conditioning effect, electricity charges,
etc.
Set the right room temperature
• In cooling operation, a temperature difference of about 5 °C [9 °F] between
indoors and outdoors is optimum.
• If the room temperature is raised by 1 °C [2 °F] during air-cooling operation,
about 10 % electric power can be saved.
• Excessive cooling is bad for health. It also results in the waste of electric
power.
Clean the filter thoroughly
• If the screen of the air filter becomes clogged, the airflow and air-
conditioning effect can be significantly reduced.
Further, if the condition is left unattended, failure can result. It is particularly
important to clean the filter at the beginning of the cooling and heating
seasons. (When profuse dust and dirt have accumulated, clean the filter
thoroughly.)
Prevent intrusion of heat during air-cooling
• To prevent the intrusion of heat during cooling operation, provide a curtain
or a blind on the window to block out direct sunlight. Also, do not open the
entrance or exit except in cases of dire necessity.
Carry out ventilation sometimes
• Since the air periodically gets dirty in a room that is kept closed for a long
time, ventilation is sometimes necessary. When gas appliances are used
together with the air conditioner, special precautions must be taken. If the
“LOSSNAY” ventilation unit developed by our company is used, you can
perform ventilation with less waste. For details on this unit, consult with your
dealer.
