Mitsubishi MOTORS M.U.T.-III Скачать руководство пользователя страница 79

Страница: 79 / 101

10-4-4. ECU reprogramming ( VCI -> Vehicle ECU )

(1) ECU parts No.and ROM-ID No. are displayed.

Press Enter key to start reprogramming.
ESC / key : restart V.C.I.

* : By pressing key, immediately move to next.

Note:
- Reprogramming must carry out on the condition of engine

stop and IG switch on.

- Do not disconnect harness/ turn off the IG switch during

ECU reprogramming.

[Messages before/during reprogramming process]

a) “RPG data doesn

’

t apply to ECU”

Reprogramming stopped owing to the data in V.C.I.memory
being not appropriate for the ECU.

•

Note down the displayed ECU parts No.and ROM-ID.

•

Restart V.C.I. by pressing Enter key, and confirm the
matching of the data file No, which is displayed by reboot,
and the ECU part No./ ROM-ID for reprogramming.

b) “ECU same as VCI, CK for new data” (CK; check)

Reprogramming stopped because reprogramming has been
already done.

Press Enter to
Reprogram ECU

ENG P/N MD351868
R-ID 120926

AT P/N MD351868
R-ID B53500

Part# MD351868
ROM-ID 120926

In case of Engine ECU

In case of PCM (Engine & A/T ECU)

Auto change in 4 sec

Press Enter to
Reprogram ECU

Auto change in 4 sec*

ECU Reprogramming

ECU same as VCI
CK for new data

Part# MD351868
ROM-ID 120926

Turn IG SW OFF,
please wait...

Auto change in 4 sec

RPG data doesn't
apply to ECU

CK VCI for
correct RPG data

Part# MD351868
ROM-ID 120926

Auto change in 4 sec

Содержание M.U.T.-III






































































































Результаты поиска

Содержание M.U.T.-III

Отзывы:

Бренды по названию

Популярные бренды

Mitsubishi MOTORS M.U.T.-III, Руководство пользователя

Результаты поиска

Содержание M.U.T.-III

Отзывы:

Бренды по названию

Популярные бренды