Mitsubishi Electric PUZ-M200YKA2 Скачать руководство пользователя страница 84

Страница: 84 / 114

OPERATING PROCEDURE

PHOTOS/FIGURES

1. Removing the service panel and top panel

(1) Remove the service panel fixing screws (4 for front/ 5 x

12), then slide the service panel downward to remove it.

(The service panel is fixed to the side panel (R) with a

hook on the right side.)

(2) Remove the top panel fixing screws (3 for front and 3 for

rear/ 5 x 12) to remove the top panel.

Note:

When removing service panel and top panel at the

same time, count one less screw since they share

a screw.

Photo 1

2. Removing the fan motor (MF1, MF2)

(1) Remove the service panel. (See Photo 1)

(2) Remove the wire grille fixing screws (4 for front/ 5 x 12),

then slide the wire grille upward to remove it. (See Photo

1) (For the each fan motor on top and under)

(3) Remove the screw of nut (1 for front/ M6), then slide

the propeller fan forward to remove it. (For the each fan

motor on top and under)

(4) Disconnect the connectors, CNF1 (WH) and CNF2 (WH)

on the controller circuit board in the electrical parts box.

(See Photo 4)

(5) Loosen the clamp for the lead wire on motor support and

separator.

(6) Release the lead wire from the hole on separator.

(7) Remove the fan motor fixing screws (4 for front/ 5 x 25)

to remove the fan motor. (For the each fan motor on top

and under)

Photo 2

Photo 3

Cover panel (rear)

Cover panel (front)

Top panel fixing screws

Top panel

Service panel

fixing screws

Service panel

fixing screws

Service panel

fixing screws

Service panel

Wire grille

fixing screws

Wire grille

fixing screws

Slide

Cover panel (front)

fixing screws

Side panel (R)

Front panel

Propeller

Nut

Fan motor

fixing screws

Fan motor

fixing screws

OCH775

14 DISASSEMBLY PROCEDURE

: Indicates the visible parts in the photos/figures.

Содержание PUZ-M200YKA2



















































































































Результаты поиска

Содержание PUZ-M200YKA2

Отзывы:

Похожие инструкции для PUZ-M200YKA2

Бренды по названию

Популярные бренды

Mitsubishi Electric PUZ-M200YKA2, Руководство по обслуживанию

Результаты поиска

Содержание PUZ-M200YKA2

Отзывы:

Похожие инструкции для PUZ-M200YKA2

Бренды по названию

Популярные бренды