Mitsubishi Electric PUZ-M200YKA2 Скачать руководство пользователя страница 29

Страница: 29 / 114

OCH775

Check Code Abnormal points and detection method

Cause

Judgment and action

(6844)

Miswiring of indoor/outdoor unit

connecting wire

1. Outdoor controller circuit board can

automatically check the number of

connected indoor units. Abnormal if the

number cannot be checked automatically

due to miswiring of indoor/outdoor unit

connecting wire, etc. after power is turned

on for 4 minutes.

2. Abnormal if outdoor controller circuit board

recognizes excessive number of indoor

units.

Contact failure or miswiring of

indoor/outdoor unit connecting

wire

Diameter or length of indoor/out-

door unit connecting wire is out of

specified capacity.

Excessive number of indoor units

are connected to 1 outdoor unit. (5

units or more)

Defective transmitting receiving

circuit of outdoor controller circuit

board

Defective transmitting receiving

circuit of indoor controller board

Defective indoor power board

2 or more outdoor units have

refrigerant address “0” .

(In the case of group control)

Noise has entered into power sup-

ply or indoor/outdoor unit connect-

ing wire.

Check disconnection or looseness or

polarity of indoor/outdoor unit connecting

wire of indoor and outdoor units.

Check diameter and length of indoor/out-

door unit connecting wire.

Total wiring length: 80 m

(including wiring connecting each indoor

unit and between indoor and outdoor unit)

Also check if the connection order of flat

cable is S1, S2, S3.

Check the number of indoor units that are

connected to one outdoor unit. (If EA is

detected)

–

Turn the power off once, and on again

to check.

Replace outdoor controller circuit

board, indoor controller board or indoor

power board if abnormality occurs

again.

Check if refrigerant addresses (SW1-3 to

SW1-6 on outdoor controller circuit board)

are overlapping in the case of group

control system.

Check transmission path, and remove the

cause.

Note: The descriptions above,

–

, are for

EA, Eb and EC.

(6845)

Miswiring of indoor/outdoor unit

connecting wire (converse wiring or

disconnection)

Outdoor controller circuit board can

automatically set the unit number of indoor

units.

Abnormal if the indoor unit number can

not be set within 4 minutes after power

on because of miswiring (converse wiring

or disconnection) of indoor/outdoor unit

connecting wire.

Contact failure or miswiring of

indoor/outdoor unit connecting

wire

Diameter or length of indoor/out-

door unit connecting wire is out of

specified capacity.

Defective transmitting receiving

circuit of outdoor controller circuit

board

Defective transmitting receiving cir-

cuit of indoor controller board

Defective indoor power board

2 or more outdoor units have

refrigerant address “0” .

(In the case of group control)

Noise has entered into power sup-

ply or indoor/outdoor unit connect-

ing wire.

(6846)

Startup time over

The unit cannot finish Startup process within

4 minutes after power on.

Contact failure of indoor/outdoor

unit connecting wire

Diameter or length of Indoor/out-

door unit connecting wire is out of

specified capacity.

2 or more outdoor units have

refrigerant address “0” .

(In the case of group control)

Noise has entered into power sup-

ply or indoor/outdoor unit connect-

ing wire.

Содержание PUZ-M200YKA2



















































































































Результаты поиска

Содержание PUZ-M200YKA2

Отзывы:

Похожие инструкции для PUZ-M200YKA2

Бренды по названию

Популярные бренды

Mitsubishi Electric PUZ-M200YKA2, Руководство по обслуживанию

Результаты поиска

Содержание PUZ-M200YKA2

Отзывы:

Похожие инструкции для PUZ-M200YKA2

Бренды по названию

Популярные бренды